background image

WARRANTY

THIS WARRANTY FORM AND CONFIRMED BUNNINGS REGISTER RECEIPT SHOULD
BE

RETAINED BY THE CUSTOMER

AT ALL TIMES

The warranty is only made available by returning the product to your nearest
Bunnings Warehouse with a 

confirmed Bunnings register receipt.

PURCHASED FROM: ________________________________________________

DATE PURCHASED: ________________________________________________

3 YEAR REPLACEMENT WARRANTY

Your Ozito tool is guaranteed for a period of 

36 months from the original date of

purchase

and is intended for DIY (Do it yourself) use only.

WARNING

The following actions will result in the warranty being void.

Professional, Industrial or high frequency use.

If the machine has been operated on a supply voltage other than that specified
on the unit.

If the machine shows signs of damage or defects caused by or resulting from
abuse, accidents or alterations.

If the machine has been disassembled or tampered with in any way.

Note:

Warranty excludes consumable parts such as rolling cutter heads, wheels
and wheel caps.

YOUR WARRANTY FORM SHOULD BE RETAINED

BY YOU AT ALL TIMES.

SHOULD YOU HAVE ANY QUESTIONS PRIOR TO

RETURNING YOUR PRODUCT FOR WARRANTY OR

REPAIR PLEASE TELEPHONE OUR CUSTOMER

SERVICE HELPLINE:

Australia 1800 069 486

New Zealand 0508 069 486

TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL NUMBER

AND DATE OF PURCHASE AVAILABLE. AN OZITO CUSTOMER SERVICE

REPRESENTATIVE WILL TAKE YOUR CALL AND ANSWER ANY QUESTIONS

YOU MAY HAVE RELATING TO THE WARRANTY POLICY OR PROCEDURE.

Summary of Contents for OZSS2500WA












Reviews: