background image

1

Motor fuel: mix at 40:1 only

Note.

 Only use oil that is expressly 

labelled for use with air-cooled 2-stroke 

engines.

Note.

 Always transport and store fuels in 

an approved container (AS2906).

1.   Fill with unleaded petrol up to fuel line.

2.   Add 2-stroke oil up to oil line. Shake 

vigorously for a thorough mix.

3.   Fill the fuel tank up to the filler neck 

with the fuel mix.

  Fuel tank capacity: 260ml

4.   Fasten the fuel tank cap and clean any 

spillage.

Chain brake/anti kickback guard

The chain brake operates automatically in the event of kick back. Kick 

back occurs if the chain catches on the wood being cut. In the event of the 

chain catching, the chainsaw will push back suddenly, when this happens, 

your hand (which is on the handle during operation) will naturally move 

forward automatically causing the guard to be pushed forward, engaging 

the chain brake and stopping the chain.

Lubrication

1.   Remove chain bar oil cap and fill 

the tank to about 80% of its capacity 

with chain bar oil.

Chain Bar Oil Tank Capacity: 210ml

Automatic oil feed system

The chainsaw is equipped with an 

automatic oil feed system. This 

delivers oil to the bar and chain.

Run the engine at medium speed 

and check that the chain splatters a 

thin line of oil which can be seen on 

the ground/material when the bar is 

pointed downwards. This may take 

15-30 seconds to occur.

Note. 

The oil outlet must be kept clear of dirt and any build-up of residue.

4.  CHAIN BRAKE & LUBRICATION

5.  FUEL

585ml 

Regular 

Unleaded

585ml 

Regular 

Unleaded

WARNING!:

 PETROL IS VERY FLAMMABLE. DO NOT 

SMOKING OR CAUSING ANY SPARKS OR FLAMES 

NEAR FUEL. MAKE SURE THAT YOU STOP THE MOTOR 

AND ALLOW IT TO COOL BEFORE REFUELLING THE 

CHAINSAW. SELECT AN OPEN OUTDOOR AREA FOR 

FUELLING AND MOVE AT LEAST 3M AWAY FROM THE 

FUELLING POINT BEFORE STARTING THE MOTOR.

CAUTION!:

 ONLY USE OIL THAT IS EXPRESSLY 

LABELLED “CHAIN BAR OIL”

WARNING!:

 NEVER START WORK UNLESS THE 

CHAIN AND BAR ARE LUBRICATED

BRAKE ON

START

BRAKE OFF

RUN

BRAKE ON

START

BRAKE OFF

RUN

2.   Fasten the chain bar oil cap 

and clean any oil spillage.

Summary of Contents for PCS-406A











Reviews: