ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
RIGHT HANDED SAW
THIS SIDE OUT
24
184
MM
TOOTH
Max. Speed 9500rpm
Bore: 20mm
Thickness: 1.6mm
TUNGSTEN
CARBIDE
TEETH
(7¼”)
WARNING!
Do not use tungsten carbide tipped blades for
masonry or metal cutting applications.
45°
30°
Installing & Removing The Battery Pack
1. Slide the battery into the tool
base until it clicks into place.
2. To remove the battery,
hold down the battery
release button and then
slide the battery out.
Attaching The Rip Fence
The rip fence allows you to perform straight cuts with ease.
WARNING!
ENSURE THE TOOL IS SWITCHED
OFF AND THE BATTERY IS REMOVED BEFORE
PERFORMING ANY OF THE FOLLOWING TASKS.
1. Insert the rip fence
through the rip fence
slots in the front of the
baseplate.
2. Once the desired width is set,
tighten the locking knob to
secure in place.
3. To remove, loosen the
locking knob and then
slide the rip fence out.
1. Dust Extraction Port
2. Rear Handle
3. On/Off Trigger
4. Lock-Off Button
5. Front Handle
6. Worklight
7. Spindle Lock Button
8. Cutting Guide Notch
9. Bevel Angle Scale
10. Hex Key Storage
11. Bevel Locking Lever
12. Upper Blade Guard
13. Rip Fence Locking Knob
14. Rip Fence
15. Blade
16. Lower Blade Guard
17. Blade Guard Lever
18. Depth Locking Lever
19. Battery Seating
This tool is compatible with all batteries & chargers from the Ozito Power X Change
range.
For optimal performance, we recommend the use of a 3.0Ah battery or higher to
operate this Power X Change Circular Saw.
CORDLESS BRUSHLESS CIRCULAR SAW
BATTERY & CHARGER
KNOW YOUR PRODUCT
1. FITTING THE BATTERY & GUIDE
SETUP & PREPARATION
RIGHT HANDED SAW
THIS SIDE OUT
24
184
MM
TOOTH
Max. Speed 9500rpm
Bore: 20mm
Thickness: 1.6mm
TUNGSTEN
CARBIDE
TEETH
(7¼”)
WARNING!
Do not use tungsten carbide tipped blades for
masonry or metal cutting applications.
RIGHT HANDED SAW
THIS SIDE OUT
24
184
MM
TOOTH
Max. Speed 9500rpm
Bore: 20mm
Thickness: 1.6mm
TUNGSTEN
CARBIDE
TEETH
(7¼”)
WARNING!
Do not use tungsten carbide tipped blades for
masonry or metal cutting applications.
RIGHT HANDED SAW
THIS SIDE OUT
24
184
MM
TOOTH
Max. Speed 9500rpm
Bore: 20mm
Thickness: 1.6mm
TUNGSTEN
CARBIDE
TEETH
(7¼”)
WARNING!
Do not use tungsten carbide tipped blades for
masonry or metal cutting applications.
a.
b.
RIGHT HANDED SAW
THIS SIDE OUT
24
184
MM
TOOTH
Max. Speed 9500rpm
Bore: 20mm
Thickness: 1.6mm
TUNGSTEN
CARBIDE
TEETH
(7¼”)
WARNING!
Do not use tungsten carbide tipped blades for
masonry or metal cutting applications.
RIGHT HANDED SAW
THIS SIDE OUT
24
184
MM
TOOTH
Max. Speed 9500rpm
Bore: 20mm
Thickness: 1.6mm
TUNGSTEN
CARBIDE
TEETH
(7¼”)
WARNING!
Do not use tungsten carbide tipped blades for
masonry or metal cutting applications.
a.
b.
2
13
3
1
5
6
7
8
19
4
18
12
15
11
9
10
17
16
14
