background image

SPECIFICATIONS

Input:  

18V

Battery Capacity: 

3.0Ah Li-ion

Power Consumption: 

54Wh

Weight:  

0.60kg

THIS MANUAL CONTAINS IMPORTANT SAFETY AND OPERATING INSTRUCTIONS FOR 

YOUR BATTERY.

1. 

Before using the charger read all instructions and cautionary markings on the charger, battery 

pack and the product using the battery pack.

2. 

This charger is not intended for any uses other than charging Ozito Power X Change rechargeable 

batteries. Any other use may result in risk of fire, electric shock or electrocution.

3. 

Do not place any object on top of the charger or place the charger on a soft surface that may 

result in excessive internal heat. Place the charger in a position away from any heat source.

4. 

To reduce risk of damage to the electric plug and cord, pull by the plug rather than the cord when 

disconnecting the charger.

5. 

Make sure the cord is located so that it will not be stepped on, tripped over, or otherwise 

subjected to damage or stress.

6. 

An extension cord should not be used unless absolutely necessary. Use of an improper extension cord 

could result in the risk of fire, electric shock or electrocution.

7. 

Do not operate the charger if it has received a sharp blow, been dropped or otherwise damaged in 

any way. Have it checked by an electrician or power tool repairer.

8. 

Do not disassemble charger. Take it to an electrician or power tool repairer when service or repair 

is required. Incorrect reassembly may result in a risk of electric shock, electrocution or fire.

9. 

To reduce risk of electric shock, unplug the charger from the outlet before attempting any clean-

ing. Removing the battery pack will not reduce this risk.

10. 

Never attempt to connect 2 chargers together.

11. 

The charger is designed to operate on standard household electrical power (240 volts). Do not 

attempt to use it on any other voltage!

12. 

The battery pack is not fully charged out of the carton. First read the safety instructions and then 

follow the charging notes and procedures.

13. 

DO NOT STORE OR USE the battery pack in locations where the temperature may reach below 0ºC 

or exceed 50ºC (such as inside sheds or metal buildings in summer). This is important and will 

prevent damage to the battery pack.

14. 

Do not incinerate the battery pack even if it is seriously damaged or is completely worn out. The 

battery can explode in a fire.

15. 

Never attempt to open the battery pack for any reason. If the plastic housing of the battery pack breaks 

or cracks, immediately discontinue use and do not recharge.

16. 

During charging, the battery must be placed in a well ventilated area.

BATTERY SAFETY WARNINGS

 ELECTRICAL SAFETY

 

WARNING! 

When using mains-powered tools, basic safety precautions, including the following, 

should always be followed to reduce risk of fire, electric shock, personal injury and material 

damage. 

Read the whole manual carefully and make sure you know how to switch the tool off in an emergency, 

before operating the tool. 

Save these instructions and other documents supplied with this tool for future reference.
Note: The supply of 230V and 240V on Ozito tools are interchangeable for Australia and New Zealand.

This tools charger is double insulated therefore no earth wire is required.

 

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly 

qualified persons in order to avoid hazard.

Note:

 Double insulation does not take the place of normal safety precautions when operating this tool. 

The insulation system is for added protection against injury resulting from a possible electrical insulation 

failure within the tool.

Using an Extension Lead

Always use an approved extension lead suitable for the power input of this tool. Before use, inspect 

the extension lead for signs of damage, wear and ageing. Replace the extension lead if damaged or 

defective.
When using an extension lead on a reel, always unwind the lead completely. Use of an extension lead 

not suitable for the power input of the tool or which is damaged or defective may result in a risk of fire 

and electric shock.
To reduce the risk of electric shock, we recommend the use of a residual current device (rated 30mA or 

less).
This appliance is not intended for use by persons (including children) with reduced physical, sensory or 

mental capabilities, or lack of experience and knowledge, unless they have been given supervision or 

instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.

 CARING FOR THE ENVIRONMENT

Power tools that are no longer usable should not be disposed of with household 

waste but in an environmentally friendly way. Please recycle where facilities exist. 

Check with your local council authority for recycling advice.

Recycling packaging reduces the need for landfill and raw materials. Reuse of 

recycled material decreases pollution in the environment. Please recycle packaging 

where facilities exist. Check with your local council authority for recycling advice.

DESCRIPTION OF SYMBOLS

Warning 

Do not store or use battery in 
temperatures exceeding 50

°

C

   

Volts

Hertz

Alternating Current

Direct Current

Milliamperes

Watts

Amp Hour

Ah

W

Hz

V

ac/~

mA

Lithium Ion Battery

Do not put in the rubbish

Do not get battery wet

Recycle Battery

Do not incinerate

dc

Regulatory Compliance

Mark (RCM)

Do not store battery when the charge 

is low; store between 40-60%.

40-60%

0%

2

1.   Battery
2.  Battery Release Button
3.  Charge Indicator Button

ozito.com.au

3

1

3.0Ah BATTERY

INSTRUCTION MANUAL

PXBP-300

Summary of Contents for POWER X CHANGE PXCG-030













Reviews: