background image

MAINTENANCE

DESCRIPTION OF SYMBOLS

STAPLE/ NAIL SELECTION

Common Applications for Staple Length

5/16” 

(8mm)

Insulation, Upholstery, Weather Stripping, 

Wall Decorations, Crafts, Covering Cornices, 

Webbing, Light Fabrics.

3/8” 

(10mm)

Insulation, Carpeting, Wire Mesh, Plastic 

or Canvas Coverings, Roofing Paper, Felt 

Stripping, Weather Stripping.

1/2” 

(12mm)

Insulation, Carpet Underlay, Porch Screens, 

Picture Frames, Wire Mesh, Netting, Roofing 

Paper, Panelling.

9/16” 

(14mm)

Ceiling Tile, Heavy Insulation, Insulation Board, 

Trellises, Roofing, Carpeting.

Common applications: C1 Brads

9/16” 

(15mm)

Trim Moulding, Panelling, Picture Frames, 

Model Work, Any Finish Nailing Application.

TYPE 53 STAPLE SIZE

18 GAUGE C1 BRAD NAIL SIZE

The SNG-2050U accepts staples with the below 

measurements

The SNG-2050U accepts nails with the below measurements

• 

When not in use, the staple nail gun should be stored in a dry, 

frost free location, keep out of children’s reach.

• 

If the housing of the staple nail gun requires cleaning, do not 

use solvents. Use of a cloth only is recommended. Never im-

merse any part of the staple nail gun into liquid.

Note:

 Ozito Industries will not be responsible for any damage or  

injuries caused by repair of the staple nail gun by an unauthorised 

person or by mishandling.

8

10
12
14

Width

11.3mm

Depth

0.75mm

Front View

Side View

Width

2mm

Front View

15

1.2mm

8

10
12
14

Width

11.3mm

Depth

0.75mm

Front View

Side View

Width

2mm

Front View

15

1.2mm

Read instruction manual

Wear eye protection

Warning 

 

 

    

 

 

ga

/min

   Gauge

 Impacts per minute

 

 

 

 

 

 

  V 

    Volts 

 

 

            Hz 

    Hertz

ac/~      Alternating current 

            W 

    Watts

 

 

SPARE PARTS

Spare parts can be ordered from the Special Orders Desk 

at your local Bunnings Warehouse or Homebase store.
For further information, or any parts visit 
www.ozito-diy.co.uk or contact Ozito Customer Service:
Great Britain: 0151 294 4488
Ireland: 1850 882711
E-mail: enquires@ozito-diy.co.uk

Summary of Contents for SNG-2050U









Reviews: