background image

11 

 

6.

 

PRODUCT

 

SERVICE 

 

The XT amplifier module MUST be serviced by a company authorized by P. Audio. 

 

Replacement of Components 

 

REPLACEMENT OF COMPONENTS MUST BE PERFORMED BY A QUALIFIED TECHNICIAN OR ONE KNOWLEDGABLE IN THE 

REPLACEMENT OF TRANSDUCER COMPONENTS! 

 

DO NOT ATTEMPT ANY REPAIRS UNLESS THE XT SERIES AMPLIFIER HAS BEEN DISCONNECTED FROM THE AC MAINS 

SOURCE!

 

 

In the event of woofer failure, the woofer may be accessed by removing the front grille and then removing the drive 

unit. This should be done by a qualified technician or contractor. There is no need to remove the amplifier panel in the 

event of a woofer failure. 

 

USE EXTREME CARE WHEN HANDLING THE XT AMPLIFIER MODULES. THE COMPONENTS ARE FRAGILE AND THE MODULE MUST 

NOT BE SET DOWN ON THE COMPONENT SIDE OR DAMAGE WILL OCCUR! 

 

NOTE: The powered models in the XT series feature an internal fuse to protect the power amplifier.  THE INTERNAL FUSE 
IS NOT USER REPLACABLE.  UNDER NO CIRCUMSTANCES SHOULD THE AMPLIFIER PANEL BE REMOVED FROM THE 
CABINET.  

 

Care should be exercised when disconnecting the amplifier module from both the woofer.   Be sure to observe the wiring polarity 

of the woofer.  

 
 

Thank you once again for purchasing this P.Audio product.  P.Audio is a manufacturer of a complete range of Loudspeaker systems, 

individual components and accessories.  For more information regarding any of P.Audio’s products or advice on how to set up and 

use this product, please do not hesitate to use the contact details on the following page to contact us. 

 

 

 

 

Please scan this QR code for quick access  

to the P.Audio website. 

 

 

 

P Audio System Co., Ltd.  19/4 Moo 2 T.Bangkratuk 

A.Samparn , Nakornpathom.  73210,Thailand 

Tel: +66-2-441 6600 (Auto 30 Lines)   

                                                                                                                               Fax: +66-2-441 6699   

                                                                                                                                                                  e-mail: info@paudiothailand.com 

                                                                                                                                             

www.paudiothailand.com

 

 

P.Audio U.S. 

div. of One Systems, Inc. 

2000 Glen Echo Rd., STE 103 

Nashville, TN  37215 

Tel: +1-615-823-1655 

Fax: +1-615-261-1429 

Email: 

info@onesystems.com

 

www.paudious.com

 and 

www.onesystems.com

  

Summary of Contents for XT Series













Reviews: