background image

Instruction Manual 

Updated11/2013

| 24

caution:

 indicates, with no symbol, that failure to conform with 

the appropriate safety measures can lead to material damage.

caution:

 indicates that failure to conform with the corres-

ponding guidelines can lead to an unwanted result or state.

If a situation presents several levels of danger, the warning notice is applied 
at the highest level in each case. If a warning notice with warning triangle 
serves to alert readers to the risk of personal injury then the warning may 
also contain an additional warning against material damage.

2.2 QualifieD electrical technician

The installation and startup of the P-CHARGE Wallbox Duo must be executed 
by a qualified electrical technician and in full compliance with this docu-
mentation. According to DIN VDE 0105-100:2009-10 3.2.3 the term Qualified 
Electrical Engineer/Technician refers to a person who, due to his/her specialist 
training, knowledge and experience as well as familiarity with the current, 
valid standards, has the capacity to assess the task assigned to him/her and 
is able to recognize potential hazards.

2.3 person instructeD in electrics

The operation of the P-CHARGE Wallbox Duo must be driven by a person 
who is fully conversant with the electrics of the system and in full compli-
ance with this documentation. According to DIN VDE 0105-100:2009-10 3.2.4 
the term "person who is conversant with the electrics of the system / person 
instructed in electrics" refers to a person who has received instruction from 
a qualified electrical technician relating to tasks assigned to him/her, as well 
as to the potential hazards of non-compliant behavior and who has been 
instructed about the safety equipment and protective measures required.

2.4 traDemark protection

P-CHARGE® is a registered trade mark of the company Schletter GmbH. The 
remaining denotations in this manual may be trademarks, the use of which 
by third parties for their own purpose may injure the rights of the proprietor.

2.5 Disclaimer

Although the contents in this instruction manual have been carefully pre-
pared, Schletter accepts no liability for the validity, accuracy, completeness 
or quality of the published information. Data provided in the instruction 
manual is checked regularly for accuracy and is updated as required. Correc-
tions are included in subsequent versions of the document.

Summary of Contents for Wallbox Duo

























Reviews: