P.I.T. Professional GSH65-C3, Operation Manual

Demolition Hammer

4

power tool accidentally.

►

Store idle power tools out of the reach 
of children and do not allow persons 
unfamiliar with the power tool or these 
instructions to operate the power tool. 

Power tools are dangerous in the hands of 
untrained users.

►

Maintain power tools. Check for mis-
alignment or binding of moving parts, 
breakage of parts and any other condi-

tion that may affect the power tool’s op

-

eration.

 If damaged, have the power tool 

repaired before use. Many accidents are 
caused by poorly maintained power tools.

►

Keep cutting tools sharp and clean. 

Properly maintained cutting tools with 
sharp cutting edges are less likely to bind 
and are easier to control.

►

Use the power tool, accessories and 
tool bits etc. in accordance with these 
instructions, taking into account the 
working conditions and the work to 
be per-formed.

 Use of the power tool for 

operations different from those intended 
could result in a hazardous situation.

►

A good knowledge of power tools re-
sulting from frequent use should not 
lead to overconfidence and neglect of 
power tool safety.

 One careless action in 

a split second can result in serious injury.

Service

►

Have your power tool serviced by a 

qualified repair person using only iden

-

tical replacement parts.

 This will ensure 

that the safety of the power tool is main-
tained.

Hammer Safety Warnings

►

ATTENTION!

 To avoid damaging the prod-

uct, never use the product as a lever.

-

The tool may vibrate during normal use. 
The screws may loosen, resulting in break-
age or accidents. Check the screw tight-
ness carefully before use.

-

Before starting work, make sure that the 
equipment is securely fastened.

-

To avoid overheating, take breaks from 
work long enough to cool the product.

►

Wear ear protectors. 

Exposure to noise 

can cause hearing loss.

►

Use auxiliary handle(s), if supplied with 
the tool.

 Loss of control can cause per-

sonal injury.

►

Hold power tool by insulated gripping 
surfaces, when performing an opera-
tion where the cutting accessory may 
contact hidden wiring or its own cord.

Cutting accessory contacting a “live” wire 
may make exposed metal parts of the 
power tool “live” and could give the opera-
tor an electric shock.

►

Use suitable detectors to determine if 
utility lines are hidden in the work area 
or call the local utility company for as-
sistance. 

Contact with electric lines can 

lead to fire and electric shock. Damaging a 

gas line can lead to explosion. Penetrating 
a water line causes property damage or 
may cause an electric shock.

►

In cold weather, or if the tool has not 
been used for a long period of time, al-
low the tool to warm up slightly by turn-
ing it on without load. 

This will soften the 

grease. Without proper warming up, the 

impact action will be difficult.

Product Description and Specifi-

cations

Read all the safety and general in-
structions

.

Failure to observe the safety and general 
instructions may result in electric shock, fire 

and/or serious injury.

Please observe the illustrations at the begin-
ning of this operating manual.

Intended use

The machine is intended for heavy chiselling 
and demolition work as well as for driving in 
and compacting with the appropriate accesso-
ries. 

Product features

The numbering of the product features refers 
to the diagram of the power tool on the graph-
ics page.
(1) Handle (insulated gripping surface)

(2) On/off switch

(3) Carrying handle
(4) Knurled nut for carrying handle
(5) Locking pin
(6) Work tool (equipment)
(7) Tool holder
(8) Oil gauge window 

Technical parameter 

Model

GSH65-C3

Rated voltage

220 V~/50 Hz

Power

2000 W

Impact frequency

2000 ipm

Impact energy

65 J

Chuck 

hex ker,30 mm 

Weight

16 kg