P.I.T. PTIG200-C, Operation Manual

Argon / Arc Welding Machine

3

switch is dangerous and must be repaired.

►

Disconnect the plug from the power 
source and/or the battery pack from the 
power tool before making any adjust-
ments ,changing accessories, or stor-
ing power tools. 

Such preventive safety 

measures reduce the risk of starting the 
power tool accidentally .   

►

Store idle power tools out of the reach 
of children and do not allow persons 
unfamiliar with the power tool or these 
instructions to operate the power tool.

Power tools are dangerous in the hands of 
untrained users.

►

Maintain power tools. Check for mis-
alignment or binding of moving parts, 
breakage of parts and any other con-
dition that may affect the power tool’s 
operation. If damaged, have the power 
tool repaired before use.

 Many accidents 

are caused by poorly maintained power 
tools.

►

Keep cutting tools sharp and clean.

Properly maintained cutting tools with 
sharp cutting edges are less likely to bind 
and are easier to control.

►

Use the power tool, accessories and 
tool bits etc. in accordance with these 
instructions, taking into account the 
working conditions and the work to be 
performed. 

Use of the power tool for oper-

ations different from those intended could 
result in a hazardous situation.

►

Keep handles and grasping surfaces 
dry, clean and free from oil and grease. 

Slippery handles and grasping surfaces do 
not allow for safe handling and control of 
the tool in unexpected situations.

Safety precautions when working 
with an argon arc welding ma-
chine 

►

Do not use the welding machine for any 
purpose other than those speci

fi

 ed in this 

manual.

►

Do not allow minors or unskilled persons 
to use the welding machine.

►

In case of transferring the welding ma-
chine to other persons, tell in detail about 
the rules of its operation and give them 
this manual.

►

Avoid the presence of children, animals 
and bystanders in the vicinity of the weld-
ing machine.

►

Do not immerse the welding machine in 
water or other liquids, and also do not ex-

pose to rain or other atmospheric precipi-
tation.

►

It is forbidden to operate the welding ma-
chine near flammable liquids or gases. 
It is forbidden to weld gas cylinders and 
containers containing 

fl

 ammable liquids or 

their vapors, as well as containers under 
pressure.

►

It is strongly discouraged to weld materials 
cleaned with chlorine-based solvents.

►

Damaged or defective electrodes are not 
recommended.

►

Make sure your network settings match 
those speci

fi

 ed in this manual.

►

Before work, check the integrity of the ca-
bles and the welding machine, the normal 
functioning of the current regulator and the 
switch without load.

►

Before connecting to the mains, make sure 
that the switch is in the off position.

►

Before turning on the device, make sure 
that the electrode is correctly installed and 

fi

 xed in the clamp, that the working surface 

is securely 

fi

 xed, that the cable plugs are 

installed and fixed in the connectors cor-
rectly in accordance with their functional 
purpose.

►

Remove all 

fl

 ammable materials from the 

work area before starting work.

►

During work, it is recommended to wear 
clothing suitable for working with the weld-
ing machine (special canvas suit, welding 
gloves to ensure safety when splashing 
molten metal).

►

A welding mask must also be used to pro-
tect the eyes.    

Product Description and Specifi-
cations

Read all safety warnings and all 
instructions. 

Failure to follow the 

warnings and instructions may result 
in electric shock, 

fi

 re and/or serious 

injury.

Intended Use

Argon / Arc Welding Machine with an addi-
tional mode of manual arc welding. These DC 
power sources are designed for the following 
welding methods:
Manual arc welding with coated electrodes 
(MMA);
Direct current argon arc welding with non-con-
tact arc ignition and shielding gas valve, 
high-frequency control by the button on the 
torch.
All machines have a digital display on the