background image

9

WARNING

Both connectors on the luminaire must be sealed 
(either with a power cord, daisy-chain connector 
cord or a cap) once installed.  Use of luminaire(s) 
with exposed connectors will void the product 
warranty.

5

Switch on the branch circuit.

ATTENTION

  

When luminaires are mounted consecutively, 
the distance between each luminaire must be a 
minimum of 8.25 in. (210 mm).  

10 cm

10 cm

8.25 in

(210 mm)

8.25 in

(210 mm)

Always ensure that cords are:

• not concealed or extended through a wall, 

floor, ceiling, or other parts of the building 
structure,

• not located above a suspended ceiling or 

dropped ceiling,

• not permanently affixed to the building 

structure,

• routed so that they are not subject to strain 

and are protected from physical damage,

• visible over their entire length, and
• used within their rated ampacity as 

determined for the maximum temperature 
of the installed environment specified in the 
instructions.

STEP 2: COMPLETE ELECTRICAL CONNECTION 
Non-dimming Applications — Daisy Chain ed Units

Hortiled Top luminaires can be “daisy-chained” in series 
with connector cables (see chart on page 10 for 
maximum number of luminaires per daisy chain).

  

1

Turn off and lock out the branch circuit. 

2

Connect the whip end of the power cord on the 
first luminaire in the daisy-chain string to branch 
circuit.

Neutral/Line 208-400V

Bond (GND)

Junction Box

Line (Hot) 208-400V

3

When daisy-chaining luminaires, remove pre-
installed connector cap(s) in 3-pin connectors on 
“power out” side of luminaire(s) between 
adjacent modules.  

TIP: 

Store removed connector caps in safe place as they will 

need to be re-installed if daisy-chain connector is ever removed. 

4

Securely connect the modules with daisy-chain 
connector cables (available in lengths of 3 ft / 6ft 
/ 10 ft / 15ft). 

drip loop

Coil and secure excess cable - allowing for drip 
loops to draw moisture away from connectors.

continues on next page...

ATTENTION

ATTENTION

power supply cord 
(non-dimming)

daisy-chain connector 
cable (non- dimming)

Summary of Contents for HORTILED Top 2.0

















Reviews: