background image

SAFETY RULES

 

 

 

•  Always start the engine and let it stabilize before connecting any electronic devices.

 

•  Disconnect all electronic devices before stopping the engine.

 

Never start or stop engine with electrical devices plugged in to the receptacles. Failure to 
do so could damage the generator and / or connected electrical devices.

 

WARNING!

 

WARNING! 

Starter and other moving parts can catch on clothing, jewelry, and hair.

 

 

•  Do not wear loose clothing or gloves.

 

•  Remove jewelry or anything else that could be caught in moving parts.

 

•  Tie back or wear protective head covering to contain long hair.

 

 

 

 

 

 

 

 

 

Check operating voltage and frequency requirements of all electrical devices prior to plugging them into the 
generator.

 

Never exceed generators wattage / amperage capacity. This could damage the generator 
and / or connected electrical devices.

 

WARNING!

 

When adding or draining fuel, unit should be turned off for at least 2 minutes to cool before removing fuel cap. If unit 
has been running then the fuel cap is under pressure, remove slowly.

 

To keep fuel from spilling, secure unit so it cannot tip while operating or transporting.

 

When transporting unit, disconnect the spark plug wire and make sure the fuel tank is empty with the 3 in 1 switch is 
turned to the off position.

 

 

 

Generator should have at least 5 feet of clearance from buildings or other equipment during operation.

 

on the unit before starting the engine.

 

Never smoke while operating or fueling this unit.

 

 

 

 

 

 

 

 

death.

 

 

WARNING!

 

•  To avoid recoil, pull starter cord slowly until resistance is felt, then pull rapidly.

 

Pull cord recoils rapidly and pulls arm towards engine faster than you can let go which 
could result in injury.

 

WARNING!

 

 

•  Allow hot components to cool beforetouching.

 

Avoid contacting hot areas of this unit.

 

WARNING!

 

Summary of Contents for P2000i





























Reviews: