Complete Radio Replacement Kit with
Integrated Climate Control Retention for
2003-2007 Honda Accord
RPK4-HD1101
P
ifi A
C
ti
Page 5
© 2018 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
Rev: V8
Date: 081318
Part Four: Kit Assembly Instructions
FIG 1
FIG 2
FIG 5
FIG 4
1.
When using a single DIN radio, snap and lock each of the side brackets onto the
supplied pocket. FIG 1
2.
When using a double DIN radio, remove the shaded tabs from the back edge of
each left and right mounting brackets (right side not shown). FIG 2
3.
Push the 4 supplied spring clips onto the 4 tabs on the back of the HONK824X
dash kit. FIG 3
4.
Using the supplied phillips head screws, line up and secure the side radio
mounting brackets to the main frame of the HONK824X dash kit. FIG 4
5.
Insert ISO mountable radio between the side mount brackets and loosely attach
to sides of radio using the screws provided with the radio when possible, or
hardware included with the kit.
6.
Move the radio’s chassis forward or backward for desired look and insert and
tighten screws.
7.
If the vehicle was equipped with a factory radio with navigation you will need to
install the navigation spacer to the top of the kit. Using 2 of the supplied screws
fasten the spacer to the top of the kit. (FIG 5) You will also need to remove the
shaded area from the center clip mount using a rotary or similar tool. (FIG 6)
8.
When using a singe DIN radio, attach a rear support bracket to the rear of the
new radio. Adjust as necessary to attach to the rear support stud, located on the
back of the pocket using the small phillips screw supplied with kit (optional).
9.
Insert the kit and radio combo into the dash. Line up the mounting tabs with the
factory mounting points. Lock the kit into the dash by applying pressure to the
face of the kit and pushing it into the dash. Secure the kit to the sub-dash using
the 3 phillips head screws removed in step 1.8 on page 2.
FIG 6
FIG 3
FIG 7
Pocket and Vehicle Assembly
Due to the position of the chassis of the aftermarket radio after installation, the cover for the factory pocket will not open and close without hitting
LW:HKDYHDGGHGD¿QLVKPDWFKHGUHSODFHPHQWSRFNHWWRWKLVNLW7KHUHSODFHPHQWSRFNHWZLOOUHTXLUHXVHRIWKHIDVWHQHUVIURPWKHIDFWRU\
pocket.
1.
Start by removing the 2 white clips at the top of the factory pocket removed in step 1.7. Clip them into the same locations on the new
pocket. See FIG 7 below for reference. Only one side is shown in the picture, but both sides will need to be done.
2.
Next remove the 2 silver screw clips at the bottom of the factory pocket. Clip them into the same locations on the new pocket. See FIG 8
below for reference.
FIG 8
3.
Install the pocket into the dash by sliding it back until the clips lock into the openings in the dash. Secure it using the two philips head
screws removed in step 1.7.
4.
Connect the front accessory power socket connector, and seat the center holder back into the dash. Secure it using the two phillips head
screws removed in step 1.6.
5.
Snap the console pocket removed in step 1.5 back into the center holder by pressing it down and forward.
6.
Install the center console front panel removed in step 1.3 and 1.4 making sure to plug the seat heater connectors back in (if equipped).
7.
Install upper panel in reverse order as removed in steps 1.1 and 1.2 making sure to plug in the hazard switch and the navigation sub
display (if equipped).
