Page 6
RPK5-GM4101
Complete Radio Replacement Kit with
Integrated Climate Control Retention for
2010-2015 Chevrolet Camaro
PAC
®
| 866-931-8021 | support@pac-audio.com
©2016 Pacific Accessory Corporation
www.pac-audio.com
Rev. 113016
Pacific Accessory Corporation
PAC is an AAMP power brand
RP5-GM4101 Optional Steering Wheel Control Programming
If you wish to re-assign the SWC functions or utilize short press long press dual command functionality, the interface must be programmed in the
specific order shown in the chart below. If you come across a function in the chart that your steering wheel does not have, or you do not want
to program, press and release the program button on the side of the interface to skip that function. The LED will flash off and on confirming that
you have successfully skipped that function and are ready to proceed to the next one.
Short Press Long Press Dual Command Functionality
This feature allows you to assign two aftermarket radio functions to each of the vehicle’s SWC buttons. It can be used with as many of the
buttons as the user likes or none at all. When this functionality is implemented, quickly pressing and releasing a SWC button will initiate the short
press command, while pressing and holding a SWC button for longer than two seconds will initiate the long press command. Please note that
all buttons except the Mute button do not have a long press command programmed by default. If you wish to assign dual command functionality
to the SWC please follow the programming steps on the next page.
Alpine
JVC
Kenwood
Clarion / Nakamichi
Other
Pioneer
Sony
Fusion
1
2
Volume -
Volume -
Volume -
Volume -
Volume -
Volume -
Volume -
Volume -
3
Mute
Mute
Mute
Mute
Mute
Mute
Mute
Mute
4
Source
Source
Source
Source
5
Preset -
Track +
Play
Preset -
Preset -
Preset -
Track +
6
Source
Track -
Track +
Search -
Source
Source
Source
Track -
7
Track +
Band/Disc +
Track -
Band
Track +
Track +
Track +
Audio
8
Track -
Preset/Disc -
Disc/FM +
Send/End
Track -
Track -
Track -
Power
9
Power
Select
Disc/AM -
Send
Band
Band
Band
10
Enter/Play
Attenuation
Answer
End
Answer
Phone Menu
Reject Call/Source
(Bluetooth equipped
radios only)
11
Band/Program
Phone Receive
Voice Dial
END
Answer Call
Answer/End Call
12
Receive
Phone Reject
On Hook
PTT
End Call
13
End
Voice Dial
Off Hook
VR
14
VR
Power
Mute (Multimedia
units only)
15
- Advent, Boyo, Dual, Lightning Audio, Jensen, Rockford Fosgate & Visteon
- Jensen & Advent ONLY
Optional Programming Order
RP5-GM4101 Testing & Verification
1.
Turn the ignition on. The LED on the interface will turn on & the +12v accessory wire will turn on.
2.
Turn on the radio and check balance & fade.
3.
Verify that all SWC are functioning properly for both the aftermarket radio and OnStar. To adjust OnStar volume, press the
OnStar button on the mirror then use the volume buttons on the SWC to adjust the level. The volume will raise a total of 8
times before returning to the original level.
4. Pressing the OnStar® button on the rearview mirror will turn off the rear speakers and allow the OnStar® audio to be heard
in the two front speakers. The OnStar® active LED will also turn on. When OnStar® disconnects, the radio will un-mute or
turn back on and the OnStar® LED will turn off. Pressing the Mute/OnStar® button on the steering wheel for 1.5 seconds
will also activate Onstar®.
5.
Turn off vehicle and remove key. RAP will be active and keep the radio on for 10 minutes, or until the driver’s door is opened.
6.
The Accessory LED and radio will turn off when RAP turns off or the driver’s door is opened.
RP5-GM4101 Product Updates (Firmware)
The RP5-GM4101 can be updated with new firmware as it becomes available using the PAC-UP interface updater (sold separately).
Please visit www.pac-audio.com/firmware for available updates.
Programming the SWC assignments
1.
Turn the key to the ignition position.
2.
Press and release the programming button on the side of the interface. The SWC LED will turn on solid.
3.
Within 7 seconds, press the button that is to be learned on the steering wheel. The SWC LED will turn off when the button is pressed.
At
this point you have two options:
A. For short press functionality:
Release the button within 1.5 seconds. The SWC LED will turn back on.
B. For long press functionality:
Hold the button until the SWC LED starts blinking. Release the button and the SWC LED will go
back to solid.
4. If you need to program more buttons, repeat step 3 for each additional audio function on the steering wheel.
5.
If you come across a function in the chart that your steering wheel does not have, or you do not want to program, press and release the
program button on the side of the interface to skip that function.
6.
Once programming is completed, wait seven seconds. The SWC LED will flash three times indicating end of programming.
7. Test the interface for proper functionality. Whenever a SWC is pressed the SWC LED on the interface should blink. If any function does
not work, repeat the programming steps.
