background image

SX-80

SX-80

SX-80

SX-80

SX-80

2

PACE Incorporated retains the right to make changes to specifications contained
herein at any time, without notice.

Contact your local authorized PACE Distributor or PACE Incorporated to obtain the
latest specifications.

The following are registered trademarks and/or servicemarks of PACE Incorporated,
Laurel Maryland U.S.A. and may only be used to identify genuine PACE products or
services:

ARM-EVAC, FLO-D-SODR, MINI-WAVE, PACE, SENSATEMP, SNAP-VAC,
SODRTEK, SODR-X-TRACTOR, THERMOFLO, THERMOJET,
THERMOTWEEZ, TOOLNET, VISIFILTER

2000 PACE Incorporated, Laurel MD.  All rights reserved.  Printed in the U.S.A.

For any questions regarding this Operation & Maintenance Manual, contact your
local authorized PACE distributor or contact PACE directly at the appropriate address
listed below.

PACE  USA

9893 Brewers Court
Laurel, Maryland 20723-1990
Tel.: (301)490-9860
       (888)535-7223 (PACE)
Fax: (301)498-3252

PACE EUROPE

Sherbourne House,  Sherbourne Drive
Tilbrook, Milton Keynes,
MK7 8HX
United Kingdom
Tel.: (44)1908 277666   Fax: (44)1908 277777

     or

www.paceworldwide.com

Summary of Contents for Sodr-X-Tractor SX-80












Reviews: