background image

SX-70

2

PACE Incorporated retains the right to make changes to specifications contained
herein at any time, without notice.

Contact your local authorized PACE Distributor or PACE Incorporated to obtain the
latest specifications.

The following are registered trademarks and/or servicemarks of PACE Incorporated,
Laurel Maryland U.S.A. and may only be used to identify genuine PACE products
or services:

Arm-Evac, Cir-Kit, ConducTweez, CRAFT, Flo-D-Sodr, Heat Wave,

HotSpot, LapFlo, MBT, Micro Portable, MicroChine, MiniChine,

Mini-Wave, PACE, Pacenter, Pik-Tip, PETS, Prep-Set, ResisTweez,

SensaTemp, Snap-Vac, Sodr-Pen, Sodr-X-Tractor, ST, StripTweez,

Thermo-Drive, ThermoFlo, ThermoJet, ThermoPart, ThermoPik,

ThermoTweez.

The following are trademarks and/or servicemarks of PACE Incorporated, Laurel
Maryland U.S.A. and may only be used to identify genuine PACE products or
services:

Sodrtek, Toolnet.

Since 1958, PACE Incorporated has provided
advanced technology training in all aspects of hand
soldering, rework and repair.

For any questions regarding this Operation & Maintenance Manual, contact your
local authorized PACE distributor or contact PACE directly at the appropriate
address listed below.

PACE Inc.

9893 Brewers Court, Laurel, Maryland 20723-1990
Tel. (888) 535-7223 (toll-free), (301) 490-9860
FAX 301 483 7030

PACE Europe Ltd.

Sherbourne House  Sherbourne Drive Tilbrook
Milton Keynes  Buckinghamshire England MK7 8HX
Tel. (44) 01908 277 666   FAX (44) 01908 277 777

© 1999 PACE Incorporated, Laurel MD.  All rights reserved.  Printed in the U.S.A.

Summary of Contents for SX-70 SODR-X-TRACTOR
















Reviews: