background image

 

 

- 24 - 

TESTING YOUR SMART TOILET SEAT 

 
When first using your Smart Toilet Seat: 

 

Insert the power plug into the socket. Your smart toilet seat’s spray nozzle should 
extend and retract initially as part of the system testing phase. 

 

Make  sure  that  the  power  indicator  light  is  on  before  testing  the  product.  The 
power light will indicate when the power is on, and the toilet won’t respond even 
if it’s connected to electricity when the power indicator light is off. 

 
1

 

Search for any water leaks before using the product 

a.

 

Make sure that all water connections are secure. 

b.

 

Turn on the water valve to confirm that there’s no water leaking. 

c.

 

Check the main unit of the toilet seat to make sure no water is leaking from 
the product. 

2

 

Confirm  all  product  features  are  functional  (

Note:

  sitting  sensor  will  only  work 

when the toilet seat is down) 

a.

 

Cover the sensor with a wet cloth or sit on the toilet. 

b.

 

Confirm that deodorizer activates. 

i.

 

Check that the air blows is blowing out correctly. 

c.

 

Verify cleaning functions. 

i.

 

Press the [SPRAY] button checking to make sure the nozzle sprays 
water. 

1.

 

The  smart  toilet  seat  needs  to  wait  1  minute  for  water  spray 
function to work upon turning the water on and 4 minutes for 
warm water after when the tank is empty. 

ii.

 

Press  the  water  pressure  adjustment  button  and  confirm  the  water 
pressure changes. 

iii.

 

Press the [STOP] button – sprayer should stop. 

d.

 

Verify Drying Functions. 

i.

 

Press the [DRYER] button to make sure warm air blows out.  

ii.

 

Press the [STOP] button – air should stop. 

e.

 

Verify that the toilet seat is heating properly. 

i.

 

It may take a few minutes for the toilet seat to heat up fully. 

f.

 

Make sure the deodorizer stops upon removing we cloth or standing – it 
takes 6 seconds for the deodorizer to deactivate. 

g.

 

Once away from the toilet the seat cover should lower automatically after 
60 seconds 

 
 

Summary of Contents for CASCADIA PB-TS03






































Reviews: