17
ALT5.CPINSB 080515-24
©PACIFIC ENERGY FIREPLACE
PRODUCTS LTD.
Maintenance
1. Burn wood only, dry and well seasoned. The denser or
heavier the wood when dry, the greater its heat value. This
is why hardwoods are generally preferred. Green or wet
wood will cause a rapid buildup of creosote. If you feel
it is necessary to burn wet or unseasoned wood, do so
only with the air inlet set open enough to maintain a good
strong fi re and fairly high chimney temperatures. Do not
attempt to burn overnight using green or wet wood. Wet
wood can cause up to 25% drop in heater output, as well
as contributing signifi cantly to creosote buildup.
WARNING: Never use chemicals or any other volatile
liquid to start a fi re. Do not burn garbage, or fl ammable
fl uids such a gasoline, naptha, or engine oil. We strongly
recommend that smoke detectors be installed.
2. Remove ashes frequently. Embers can roll out the door
and create a fi re hazard. Maintain a 1" minimum ash base.
3. If glass becomes darkened through slow burning or poor
wood, it can readily be cleaned with any fi replace glass
cleaner when stove is cold. Never scrape with an object
that might scratch the glass. The type and amount of
deposit on the glass is a good indication of fl ue pipe and
chimney buildup. A light brown, dusty deposit that is eas-
ily wiped off usually indicates good combustion and dry,
well-seasoned wood and, therefore, relatively clean pipes
and chimney. On the other hand, a black, greasy deposit
that is difficult to remove is a result of wet and green wood
and too slow a burning rate. This heavy deposit is building
up at least as quickly in the chimney.
WARNING: Only use materials supplied by the manufac-
turer when doing maintenance or replacements.
4. DOOR GASKET - The gasket used by Pacifi c Energy
requires only light pressure to seal. This will prolong seal
life. It is important that the door seal be maintained in
good condition. Periodically inspect seals and replace if
necessary.
5. DOOR GLASS - Do not slam loading door or otherwise
impact glass. When closing door, make sure that no logs
protrude to contact the glass. If the glass gets cracked or
broken, it must be replaced before using the stove. Re-
placement glass can be obtained from your Dealer. The
size required is 11-3/8 x 17-1/4 x 5 mm. Ceramic glass
must be used. Do not substitute with any other type.
To remove broken glass, undo the four retaining screws and
remove the clamps, noting position for re-assembly. Remove
all particles of glass. Be careful, as they are very sharp. Install
new glass complete with gasket. Replace clamps and screws.
WARNING: Do not overtighten, tighten screws very care-
fully.
- Do not clean glass when hot
- Do not use abrasive cleaners on glass
6. The area where boost combustion air enters the fi rebox
must be kept clear of excessive ash buildup which will
block air fl ow. This area is at the front of the fi rebox.
7. Do not store wood within heater installation clearances,
or within the space required for fuel loading and ash re-
moval. Keep the area around the heater clean and free
of all combustibles, furniture, newspapers, etc.
8. If a plated door requires cleaning, use mild soap and water
only. Use of abrasive cleaners will void warranty.
9. Establish a routine for the fuel, wood burning and fi ring
technique. Check daily for creosote buildup until experi-
ence shows how often you need to clean to be safe.
10. Be aware that the hotter the fi re, the less creosote is
deposited. Weekly cleaning may be necessary in mild
weather, even though monthly cleaning is usually enough
in the coldest months when burning rates are higher.
11. Instruct all members of your family on the safe operation
of the heater. Ensure they have enough knowledge of the
entire system if they are expected to operate it. Stress the
section on chimney fi res and the importance of following
the steps outlined in “In Case of Chimney Fire”.
Baffle Removal
The Insert and pipe should be removed from the fi replace
to clean and inspect. Only if this is not possible should you
remove baffle assembly.
DO NOT OPERATE WITH BAFFLE ASSEMBLY OR INSULA-
TION REMOVED.
Baffle Assembly Removal
Remove retaining pin at the back top of the fi rebox, just under
the baffle. Lift baffle up and pull forward to disconnect from
the supply tube. Tilt baffle sideways to drop down and remove
from fi rebox.
Inspect gasket between baffle and supply tube. If necessary,
replace with gasket # 139.5 available from your nearest Pacifi c
Energy Dealer.
Re-install baffle assembly and insulation by reversing order.
It is recommended to inspect the liner and connector
monthly and to have the liner cleaned annually or more
frequently if required.
