47
46
11
10
WINTERIZING
We recommend that you always have your spa filled with water and running at normal spa temperatures (27°C/80°F to
38°C/100°F). This will help reduce the risk of freezing your spa and it’s equipment.
warning
:
freeze
damage
will
void
the
warranty
coverage
.
1. Shut the power off to the system and ensure that it cannot be accidentally turned back on.
2. Open all filter covers.
3. Remove the filter baskets and filters.
4. Drain your spa completely.
5. Remove drain plugs from the front of the pumps.
6. Disconnect the unions from both sides of the pump.
7. Use a wet/dry vacuum to blow any remaining water out of the jets and equipment area.
8. Replace drain plugs from the front of the pumps.
9. Reconnect the unions from both sides of the pump.
10. Using a long funnel, pour non-toxic swimming pool or recreational vehicle water system antifreeze into the filter canister
fittings, bleeder valve fittings and jet fittings of your system. Continue adding antifreeze until it spills out of the drain fittings or
from the opening you are pouring it into. You must complete this task for every jet fitting in the system as well as the pumps
and the bottom drain.
11. Cover your spa with a good spa cover and an all-weather tarp or spa bag to ensure that neither rain nor snow enter the spa.
emergency
situations
:
To eliminate freezing in the event of equipment failure, use a small heater with temperature control via
extension cord and place it in the equipment area, keeping it away from plumbing lines. This will help for a short period of time
until proper service can be arranged. You can also add hot water to the spa (only when full) while using the heater to help keep the
smaller plumbing lines from freezing.
CHEMISTRY
Basic Chemical Safety
It is essential to read chemical container labels and follow the directions carefully. The following guidelines must be observed:
∙ Keep all chemicals out of reach of children.
∙ Chemicals may be corrosive, so handle with care. Store in a cool, dark place
∙ Do not inhale fumes or allow chemicals to come in contact with face or eyes. Wash hands after use.
∙ Ensure any spilled chemicals are carefully cleaned up. They may be corrosive and may cause damage or bodily harm.
∙ Never smoke near chemicals, some are highly flammable.
∙ If chemicals are swallowed or come in contact with your eyes or irritation occurs, follow the emergency instructions on the
container.
∙ Accurately measure and use exact quantities specified – never more than what is recommended.
∙ Never add concentrated chemicals directly into the spa. Dilute with water in a large plastic pail.
∙ Always add chemicals to water and never water to chemicals.
∙ Do not mix chemicals with each other before adding to the spa. Add only one chemical at a time.
∙ Ensure the jet pump is on high speed while adding chemicals to the spa. Leave the jet pump running for at least 15 minutes
to properly disperse the chemicals.
∙ When shocking the spa, leave the spa cover off for 20 minutes to allow oxidizer gas to vent.
∙ Discolouration or damage due to chemicals is not covered under the Limited Warranty.
Start Up Chemicals and General Supplies
Here is a basic list of chemicals and supplies needed before you use your spa. The availability of certain chemicals may vary from
one dealer to another. See your local dealer for these items and directions on how to use them properly:
∙ Stain and scale inhibitor – neutralizes metals, clarifies water and helps prevent scaling.
∙ Alkalinity increaser – raises total alkalinity, buffers against erratic pH fluctuation.
∙ PH up – raises the pH of the spa water.
∙ PH down – lowers pH of the spa water.
∙ Calcium hardness increaser – protects against the effects of soft water, which can cause corrosion to some components in
your spa.
∙ Spa shock – oxidizes organic compounds, clarifies water.
∙ Spa sanitizer – bromine or chlorine tablets are the main source of chemical sanitation.
∙ Filter cleaner – for soaking and cleaning dirty filter cartridges.
Chemical balance chart for recommended levels:
effective
range
Total Alkalinity (TA)
125–150 ppm
pH Level
7.4–7.8
Calcium Hardness (CH)
80–100 ppm
Total Dissolved Solids (TDS)
<1500 ppm
Sanitizer (Chlorine/Bromine)
3–5 ppm
