ADJUSTMENTS AND INSPECTIONS
26B AND 32B
BRUSH ADJUSTMENT CONTINUED
2. The rear section of the brushes should touch the floor at the same time. The front of the brushes should be
about 5 to 8 mm (0.2 to 0.3 inches) higher than the rear section. Adjust the support forward or backward if
necessary. Also adjust the screw limit stop to avoid any moving part touching the support.
Note: If the front of the brushes are too high, the machine will pull to the right and it lead to uneven brush wear.
3
.
Adjustment of thetwo lift arms and pressure springs: Turn the screw in each fork to adjust the spring compres-
sions to 78 to 80 mm (about 3.1 inches). Tighten the nuts.
4. With the brush base lifted adjust the screw M10 (rest arm support) so the brush base cover doesn’t touch the
tank or the frame. Tighten the nut.
ACTUATOR ADJUSTMENT
1. Bend the metallic lever of the microswitch so that the brush base rise is stopped when the control lever is
aproximately 5 mm (0.2 inches) from the microswitch support.
2. Utilize the maximum pressure notch on the adjustment lever. Then lower the brush base until the microswitch
of the limit stop releases. Now verify that the worm still has 10 mm (0.4 inches) of run. If not, adjust the
preloading on the spring tie rod.
Location
Drawing 01-Item 04-Page 2
Drawing 03-Item 11-Page 6
Drawing 03-Item 19-Page 6
Drawing 03-Item 15-Page 6
Drawing 03-Item 16-Page 6
Drawing 03-Item 18-Page 6
Drawing 03-Item 71-Page 6
Drawing 01-Item 27-Page 2
Location
Drawing 13-Item 15-Page 26
Drawing 03-Item 05-Page 6
Drawing 13-Item 14-Page 26
Drawing 13-Item 02-Page 26
Drawing 13-Item 16-Page 26
Drawing 13-Item 08-Page 26
Drawing 13-Item 20-Page 26
Drawing 05-Item 58-Page 10
37
https://harrissupplyind.com - To Order Parts Call 608-268-8080
Summary of Contents for ScrubMaster 32B
