SPECIFICATION
The Pacific Wolverine PF7 Edger Sander will sand
hard and soft wood floors, cork and composition
floors and any solid wood surface that requires rapid
sanding and leveling to a fine finish. Ideal for
confined areas such as closets and stair treads the
will sand right up to the edge of
a floor without damage to the base (skirting) board.
Completely self contained with a high efficiency dust
pick-up the
is a high
performance sander suitable for professional and
home owner use.
Pacific Wolverine PF7
Pacific Wolverine PF7
SAFETY
1.
For safety it is recommended that a residual
current circuit breaker (ground fault interrupter)
is used with this machine.
2.
Check the operating voltage is correct and that
the machine is switched OFF (O) before
connecting to the power supply.
3.
Never attempt to lock the switch in the ON (I)
position with tape or by any other means.
4.
Always disconnect from the power supply when
changing the abrasive disc, servicing the floor
sander, replacing the dust bag or leaving the
machine unattended.
5.
Always replace the dust bag (paper type) or
empty the dust bag (cloth type) when the dust in
the bag reaches the ‘MAX’ line or when the
machine is left unattended.
6.
Never dispose of or empty the contents of the
dust bag into a fire or incinerator.
7.
Never reuse the paper dust bag or use a non
standard bag. Cloth type bags must be in good
condition with no holes.
8.
Always wear a dust mask when using the floor
sander, handling the dust bag or cleaning the
machine after use.
9.
Wear ear protection when using the floor sander.
10. Ensure adequate ventilation of the work area to
avoid the formation of a combustible mixture of
flying dust and air.
11. Never smoke when using or servicing the floor
sander or when handling the dust bag.
12. Never expose the machine to rain or damp.
Always store in a dry place.
13. Stop the floor sander immediately if damage to
the machine or abrasive disc is suspected.
14. Never allow the power cable to come into contact
with the sanding disc when the floor sander is in
operation. If the power cable becomes damaged
and the inner conductors are exposed switch the
power OFF and remove the plug before
attempting to move the machine. The cable must
be replaced by an authorized agent or qualified
electrician using genuine Pacific Floor Care
spare parts only.
15. Keep hands, feet and loose clothing away from
all moving parts of the machine.
16. Punch down or remove all nails, screws, tacks
and other fixings from the floor before sanding to
prevent contact with the sanding disc.
17. Never use the machine above waist height as
control will be lost.
18. Keep children and pets clear at all times.
19. If the machine should fail to operate refer to the
fault finding guide on page 8.
1
CAUTION - read the following Safety
and Operational notes before using your
.
Pacific Wolverine PF7 Edger Sander
Noise:
100 dBa at 1metre (3’ 3")
Switch:
Bias Off, double pole.
Motor RPM:
13,000
Disc RPM:
3,000
Moving Parts:
Sealed for life ball bearings.
Weight:
16.4kg (36.2lbs)
0.04 M² H Aeq8
(8 Hr. RMS )
7" (178") dia. x 7/8“ (22mm) dia.
centre hole. 24 to 120 grit fibre or
paper back.
Abrasive:
Continuous heavy duty AC/DC self
cooling 4 brush.
7" (178mm) dia. Metal backed and
rubber bonded.
High impact ABS with bronze bush.
Hardened steel alloy pinion and
large diameter aluminium bronze
drive gear.
Seated oversize vacuum fan,
disposable paper dust or cloth
bag.bags
Disc Guard:
Drive:
110/120 V 50/60 Hz
220/240 V 50/60 Hz
110/120 V 8A
220/250 V 5A
Average
Load Current:
110/120 V 15A
220/250 V 8A
Dust Pickup:
Vibration:
Power Supply:
Off Load
Current:
Motor:
Sanding Pad:
