background image

WARRANTY POLICY

AUTO SCRUBBER, Z210 TRACTION

The 

Pacific 

Z210 traction auto scrubber has been manufactured, tested and inspected in accordance with specific engineering requirements.  This machine is WARRANTED to be free from defects in 

workmanship and materials for periods as follows from the date of purchase. 

Travel time for warranty repair is authorized for a period of ninety (90) days following the date of sale to the end user, with a maximum of three (3) hours per claim.

This warranty extends to the original user/purchaser and only when used, operated and maintained in accordance with 

Pacific

 Operating and Maintenance instructions.

This warranty does not apply to certain wear parts and accessories of the machine such as carbon motor brushes, floor brushes or pad drivers, belts, hoses, squeegee blades, etc., nor does it apply 

to damage or failure caused by improper use, abuse or neglect.  Warranty credit or replacement of return parts including motors, switches, etc., is subject to incoming inspection of those items.

To secure repair under this warranty, the following procedure should be taken:

1. 

After the expiration of the ninety (90) day travel time warranty period, the customer is responsible for warranty travel payment or the inoperative machine or warranted parts must be delivered 

to the authorized dealer with shipping and delivery charges prepaid.  If unable to locate the Dealer, you may contact 

Pacific 

at the address listed herein for the location of the nearest 

Pacific 

repair 

center or agent or for other instructions pertaining to your warranty difficulty.

2. 

 Upon compliance with the above warranty procedure, all warranted repairs will be completed at no additional charge or cost to the user.

3.

  Only 

Pacific

 or its authorized dealers and agents may make no charge warranty repairs on this product.  All others do so at their own risk.

This warranty limits 

Pacific 

 liability to the repair of the product and/or warranted parts replacement and does not include incidental or consequential damages arising from the use of a 

Pacific 

 

machine whether defective or not.  

BATTERY WARRANTY

In addition to the terms above, any original equipment 

Pacific

 Battery which becomes unserviceable under normal use within a period of ninety (90) days from date of sale to the original user 

will be repaired or replaced with one of equal specification at our option, F.O.B. any authorized Pacific or Service Branch, with no charge to user, except transportation costs.  After the expiration 

of the above ninety (90) day period, any battery which fails under normal use will be adjusted to the original user with a new battery of equal specification on a twelve (12) month pro rata basis 

from the date of purchase.  Adjustment will be determined using the then current list price, plus transportation costs.  Warranty is rendered null and void if battery maintenance is not performed 

regularly.  

This warranty is in lieu of all other expressed or implied warranties and is extended to the original purchaser/user.

Two (2) Years Parts, One (1) Year Labor  – Brush Drive Motors

One (1) Year Parts & Labor – All other components unless excluded below

2259 S. SHERIDAN DRIVE

MUSKEGON, MICHIGAN 49442-6252

800-968-1332

FAX  800-863-9536

10/12

Ten (10) Years Parts, One (1) Year Labor  – Polyethylene Components

Five (5) Years Parts, One (1) Year Labor  – Main Frame

Summary of Contents for Z210




































Reviews: