background image

Chapter 2

33

Setting a Password

Follow these steps as you set the user or the supervisor password:

1.

Use the 

 and 

↓ 

keys to highlight the Set Supervisor Password parameter and press the 

Enter

 key. The 

Set Supervisor Password box appears:

2.

Type a password in the “Enter New Password” field. The password length can not exceed 8 alphanumeric 
characters (A-Z, a-z, 0-9, not case sensitive). Retype the password in the “Confirm New Password” field.

IMPORTANT:

Be very careful when typing your password because the characters do not appear on the screen.

3.

Press

 

Enter

.

 After setting the password, the computer sets the User Password parameter to “Set”.

4.

If desired, you can opt to enable the Password on boot parameter.

5.

When you are done, press F10 to save the changes and exit the BIOS Setup Utility.

Removing a Password

Follow these steps:

1.

Use the 

 and 

 keys to highlight the Set Supervisor Password parameter and press the 

Enter

 key. The 

Set Password box appears:

2.

Type the current password in the Enter Current Password field and press 

Enter

.

3.

Press 

Enter

 twice 

without

 typing anything in the Enter New Password and Confirm New Password fields. 

The computer then sets the Supervisor Password parameter to “Clear”.

4.

When you have changed the settings, press 

u

 to save the changes and exit the BIOS Setup Utility.

S e t   S u p e r v i s o r   P a s s w o r d

E n t e r   N e w   P a s s w o r d                 [                               ]

[                               ]

C o n f i r m   N e w   P a s s w o r d                 [                               ]

S e t   S u p e r v i s o r   P a s s w o r d

E n t e r   C u r r e n t   P a s s w o r d                 [                               ]

[                               ]

E n t e r   N e w   P a s s w o r d                 [                               ]

C o n f i r m   N e w   P a s s w o r d                 [                               ]

[                               ]

Summary of Contents for EasyNote LJ75































































































































































































































Reviews: