background image

 

 

 

coasters do  not flash consistently, this is your maximum range. If you would like to 
increase your  power level, exit range test and call Pagertec.   

• Press the 

“CANCEL” 

key to stop the range test. Press the 

“CANCEL” 

key again to exit 

the system programming menu. 

Note: 

The transmitter has an auto shut off feature that will 

stop the Field Test after 15 minutes.  

SET KEY TONE  

With this Feature you can turn 

ON

/

OFF 

the beeping sound of the transmitter when the 

buttons are being pressed on the transmitter. To change the option press 

“ENTER” 

and 

use the up and down arrow until you select your desired choice. Then Press 

“ENTER”

 

                           FCC COMPLIANCE AND ADVISORY STATEMENT   

 

This device complies with Part 15 of the FCC rules. Operation is subject to the 

following  

two conditions: (1) 

this device may not cause harmful interference, and 

(2) 

this device  must accept any interference received, including interference that may 
cause undesired  operation.   

This equipment has been tested and found to comply with the limits for a Class B digital 
device, according to Part 15 of the FCC rules. These limits are designed to provide 
reasonable protection against harmful interference in a residential installation. This 
equipment  generates, uses and can radiate radio frequency energy and if not installed 
and used in  accordance with the instructions, may cause harmful interference to radio 
communications.  However, there is no guarantee that interference will not occur in a 
particular installation. If  this equipment does cause harmful interference to radio or 
television reception, which can be  determined by turning the equipment off and on, the 
user is encouraged to try correct the  interference by one or more of the following 
measures:   

 

Summary of Contents for Smart Stack EVO












Reviews: