Painless Performance Products 20110 Installation Instructions Manual Download

Page: 27 / 30

Color

Ga. No.

Connect to

Wire Starting Point

Section of Starting

Point

WIPER SWITCH

SECTION

Blu

986 Wiper Switch

Wiper Motor

Wiper Motor Section

LtBlu

987 Wiper Switch

Wiper Motor

Wiper Motor Section

Blk

988 Wiper Switch

Wiper Motor

Wiper Motor Section

WIPER MOTOR

SECTION

Ylw

989 Wiper Motor Power

Fuse Panel

Blu

986 Wiper Motor

Wiper Switch

Wiper Switch Section

LtBlu

987 Wiper Motor

Wiper Switch

Wiper Switch Section

Blk

988 Wiper Motor

Wiper Switch

Wiper Switch Section

INSTRUMENT PANEL

SECTION

Brn/Wht

970 Charge Light

Fuse Panel

Brn/Wht

914 Charge Light

Alternator

Alternator Section

LtGrn

936 High Beam Indicator

Dimmer Switch

Dimmer Switch Section

LtBlu

937 Left Turn Indicator

LF Turn Signal

Turn Signal Switch Section

Blu

938 Right Turn Indicator

RF Turn Signal

Turn Signal Switch Section

Gry

930 Instrument Panel Lighting

Headlight Switch

Headlight Switch Section

Tan

939 Fuel Gauge

Fuel Sending Unit

Tail Section

Grn

921 Temp. Light

Temp. Sending Unit

Engine Section

Blu

922 Oil Light

Oil Pres. Sending Unit

Engine Section

Orn

981 Clock Power

Fuse Panel

Blk/Wht

975 Ground

Instrument Panel

Instrument Panel Section

Tan

962 Brake Warning Light

Pressure Switch &

Emergency Brake

Engine & Dash Sections

RADIO SECTION

Red

940 Radio Power Unswitched

Fuse Panel

Ylw

941 Radio Power Switched

Fuse Panel

DOME LIGHT SECTION

Wht

961 Dome Light (Ground)

Headlight Switch

Headlight Switch Section

Orn

945 Dome Light (Power)

Fuse Panel

TAIL SECTION

Grn

948 RR Turn Signal

Turn Signal Switch

Turn Signal Switch Section

Ylw

949 LR Turn Signal

Turn Signal Switch

Turn Signal Switch Section

Tan

939 Fuel Sending Unit

Fuel Gauge

Instrument Panel Section

Brn

929 Tail Lights

Headlight Switch

Headlight Switch Section

Lt.Grn

956 Backup Lights

Backup Switch

Dash Section

Table 10.2 Wire Connection Index (3 of 3)

NOTES:

This wire is used only on the `67 model vehicle, if wiring a `66 model you will tape and stow

this wire.

This wire is power for the portion of the headlight switch that goes out to the headlights and

front parking lights.
3.

This wire is power for the portion of the headlight switch that goes out to the instrument

panel lights and the taillights.
4.

See Diagram1, page 23 for connection instructions.

Summary of Contents for 20110































Search results

Summary of Contents for 20110

Reviews:

Related manuals for 20110

Brands by name

Popular brands

Painless Performance Products 20110, Installation Instructions Manual

Search results

Summary of Contents for 20110

Reviews:

Related manuals for 20110

Brands by name

Popular brands