background image

16 

ECM CONNECTION 

 

In  some  race  applications,  you  may  want  to  have  components 

controlled with either a toggle or rocker switch AND an aftermarket 
ECM (Engine Control Module). If this is the case, the Track Rocker is 
designed to allow BOTH a grounding switch and an aftermarket ECM 
to  ground  the  85(-)  terminal  on  the  coil  inside  of  the  relay.  This  is 
commonly referred to as “sinking the relay to ground.” All the relays 
in the Track Rocker are ‘diode suppressed,” therefore; it is CRITICAL 
the 85(-) terminal is ONLY used as ground control.   

This  redundancy  allows  you  to  manually  operate  components, 

like the cooling fans, while still allowing them to function automatically 
as programmed into a microcontroller. Most aftermarket ECM’s can 
be  tied  into  the  Track  Rocker  System.  To  do  so  simply  splice  the 
appropriate  grounding  output  wire(s)  from  the  ECM  into  the  Switch 
Control Pigtail wires.  

 

Doing this allows either the switch or the ECM to complete the 

circuit within the relay and activate the relay’s output wire. This will 
also  illuminate  the  lighted  switches  to  illuminate  whether  the 
component was activated manually by the switch or automatically by 
the  computer,  thus  signaling  the  driver  anytime  the  component  is 
active.  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for Track Rocker series

























Reviews: