background image

Revision 01

Section 350-231-172

HLU-231 List 7B

15

ALRM

Alarm Condition 
Exists

A minor alarm condition is in effect.

1=xx or 2=yy

HDSL Loop 
Margins

Indicates the relative S/N at each HDSL 
transceiving input port.  Any value of ‘06’ 
or greater is adequate for reliable system 
operation.

PWR FEED 
SHRT

Power Feed Short

Indicates a short between the 2 HDSL 
pairs in span 1.  This same message can 
occur with an HRU is drawing the correct 
amount of power over good cable pairs 
but cannot communicate with the HLU.

PWR FEED 
OPEN

Power Feed Open

Indicates an open circuit in both the tip 
and ring of either HDSL pair in span 1.

BAD RT?

No response from 
HRU

The HLU does not receive any 
response from the HRU.  Thus, the HRU’s 
integrity is questionable.

VER

HLU Software 
Version #

This is displayed during the System 
Settings review mode.  (Depress the 
MODE button for 3 seconds to enter Sys-
tem Settings review mode.)

LIST 0xL

HLU’s List #

Displayed during System Settings 
review mode defined above.

FRM

Frame: SF, ESF, 
UNFR, NONE

Defines the type of frame pattern 
being received from the DSX-1.  
Displayed during System Settings.

CODE

Line Code: AMI, 
B8ZS

This is the line code that the HLU is set to 
receive and transmit at its T1 
interfaces.  Displayed during System 
Settings mode defined above.

Diagnostic Messages (Continued)

Message

Full Name

Description

† 

These messages only apply to systems with doublers present.

Summary of Contents for 150-1111-72





















Reviews: