background image

 

C

ERTIFICATION

 

AND

 W

ARRANTY

FCC C

OMPLIANCE

This equipment does not have any clocking source and is a passive device per FCC guidelines. When used in conjunction with any clocking 
devices, this combined system may radiate radio frequency energy that causes harmful interference to radio communications. Operating such 
a system in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his 
own expense.

L

IMITED

 W

ARRANTY

 

ADC DSL Systems, Incorporated (“ADC”) warrants that, for a period of sixty (60) months from the date of shipment, the hardware portion 
of its products will be free of material defects and faulty workmanship under normal use. ADC's obligation, under this warranty, is limited to 
replacing or repairing, at ADC's option, any such hardware product which is returned during the 12-month warranty period per ADC's 
instructions and which product is confirmed by ADC not to comply with the foregoing warranty.

ADC warrants that, for a period of 90 days from the date of purchase, the software furnished with its products will operate substantially in 
accordance with the ADC published specifications and documentation for such software. ADC’s entire liability for software that does not 
comply with the foregoing warranty and is reported to ADC during the 90-day warranty period is, at ADC’s option, either (a) return of the 
price paid or (b) repair or replace of the software. ADC also warrants that, for a period of thirty (30) days from the date of purchase, the media 
on which software is stored will be free from material defects under normal use. ADC will replace defective media at no charge if it is returned 
to ADC during the 30-day warranty period along with proof of the date of shipment.

The transportation charges for shipment of returned products to ADC will be prepaid by the Buyer. ADC will pay transportation charges for 
shipment of replacement products to Buyer, unless no trouble is found (NTF), in which case the Buyer will pay transportation charges.

ADC may use reconditioned parts for such repair or replacement. This warranty does not apply to any product which has been repaired, worked 
upon, or altered by persons not authorized by ADC or in ADC's sole judgment has subjected to misuse, accident, fire or other casualty, or 
operation beyond its design range.

Repaired products have a 90-day warranty, or until the end of the original warranty period—whichever period is greater. 

ADC DISCLAIMS ALL OTHER WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED 
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO ITS PRODUCTS 
AND ANY ACCOMPANYING WRITTEN MATERIALS. FURTHER, ADC DOES NOT WARRANT THAT SOFTWARE WILL BE 
FREE FROM BUGS OR THAT ITS USE WILL BE UNINTERRUPTED OR REGARDING THE USE, OR THE RESULTS OF THE USE, 
OF THE SOFTWARE IN TERMS OF CORRECTNESS, ACCURACY, RELIABILITY OR OTHERWISE.

 R

ETURNS

ADC continues to repair faulty modules beyond the warranty program at a nominal charge. Contact your ADC sales representative for details 
and pricing. Refer to the instructions under “Appendix C - Product Support”

 on page 38

 for complete return instructions.

M

ODIFICATIONS

Any changes or modifications made to this device that are not expressly approved by ADC Telecommunications, Inc. voids the user's warranty.

All wiring external to the products should follow the provisions of the current edition of the National Electrical Code.

S

TANDARDS

 C

OMPLIANCE

This equipment has been tested and verified to comply with the applicable sections of the following standard:

TR-TSY-00056: Repeater Housings for T1, T1C, T1D, and T1G Carrier Systems

Summary of Contents for HiGain HRE-458





















































Reviews: