background image

11

51-3000

INSTALLATION

6.  Raise the brush head assembly using the lift 

system. If the brush head assembly raises 4 

inches (101mm) off the ground, the lift cable 

is properly adjusted; otherwise, go to the next 

step.

7.  Adjust the cable.

•  If the brush head assembly does not raise 

enough, decrease the amount of cable 

between the uprights.

•  If the brush head assembly raises too much, 

increase the amount of cable between the 

uprights.

Spring-Chain Assembly, Transport Chain & Lift Cable

Refer to figures 6 & 7.

1.  Connect 2, 26-link chains and 2 springs to form 

a loop.

2.  Place chains in the outside slots in the drive 

assembly upright and in the brush head 

assembly upright.

3.  Route 1 end of the lift cable through the chain 

link welded to the brush head assembly upright. 

Loop the loose end around and secure it with a 

cable clamp (figure 5).

CAUTION!  INSTALL CABLE CLAMPS AS 

SHOWN

 

IN FIGURE 5; 

otherwise; 

the cable could slip, possibly 

damaging the sweeper or injuring the 

operator.

4.  Loop the other end through the link on the drive 

assembly upright; secure it with a cable clamp.

5.  Place the 36-link transport chain in the center 

slot in the drive assembly and in the brush head 

assembly upright.

6.  Slide a pin in the holes under the drive assembly 

upright and a pin in the holes under the brush 

head assembly. Insert a hairpin clip in each pin.

7.  Hook up the electric lift system or optional 

hydraulic lift system.

figure 4

figure 5

figure 6

figure 7

Summary of Contents for Sweepster M24 Series































































Reviews: