background image

4

51-3000

INTRODUCTION

Purpose of Sweeper

This sweeper is designed solely for the use in 

construction cleanup, road maintenance and similar 

operations. Use in any other way is considered 

contrary to the intended use. Compliance with and 

strict adherence to operation, service and repair 

conditions, as specified by the manufacturer, are 

also essential elements of the intended use.

Contacting Sweepster

If you have any questions about information in this 

manual or need to order parts, please call, write, fax 

or e-mail SWEEPSTER.

Sweepster

2800 North Zeeb Road

Dexter, Michigan 48130

Phone: (734)-996-9116 - (800)-456-7100

Fax: (734) 996-9014

e-mail: sweepster@paladinbrands.com

For help with installation, operation or maintenance 

procedures, contact our Technical Service 

Department. Direct product questions and parts 

orders to our Sales Department.

When ordering parts or accessories, be prepared to 

give the following information:

•   Sweeper model, serial number and date of

    purchase

•   Prime mover, make and model

•   Part number, description and quantity

Terms Used in Manual

Right-hand, left-hand, front

 and 

rear

 are determined 

from the operator’s perspective (either the 

operator’s seat or standing behind a walk-behind 

unit), facing forward in the normal operating 

position. 

Warranty

To validate the warranty for this unit, fill out the 

warranty card or warranty pages located in the 

back of this manual. Then send this information to 

SWEEPSTER.

SAFETY STATEMENTS

DANGER! 

THIS STATEMENT IS USED 

WHERE SERIOUS INJURY OR 

DEATH WILL RESULT IF THE 

INSTRUCTIONS ARE NOT 

FOLLOWED PROPERLY.

WARNING!  THIS STATEMENT IS USED 

WHERE SERIOUS INJURY OR 

DEATH COULD RESULT IF 

THE INSTRUCTIONS ARE NOT 

FOLLOWED PROPERLY.

CAUTION!  THIS STATEMENT IS USED 

WHERE MINOR INJURY COULD 

RESULT IF THE INSTRUCTIONS 

ARE NOT FOLLOWED PROPERLY.

NOTICE! 

THIS STATEMENT IS USED 

WHERE EQUIPMENT OR 

PROPERTY DAMAGE COULD 

RESULT IF THE INSTRUCTIONS 

ARE NOT FOLLOWED PROPERLY.

 

THIS SYMBOL BY ITSELF OR 

USED WITH A SAFETY SIGNAL 

WORD  THROUGHOUT THIS 

MANUAL IS USED TO CALL YOUR 

ATTENTION TO INSTRUCTIONS 

INVOLVING YOUR PERSONAL 

SAFETY OR THE SAFETY OF 

OTHERS. FAILURE TO FOLLOW 

THESE INSTRUCTIONS CAN 

RESULT IN INJURY OR DEATH.

Summary of Contents for Sweepster M24 Series































































Reviews: