Palazzetti MULTIFIRE BIO 14 Installation, Use And Maintenance Manual Download

Page: 49 / 144

ENGLISH

USE AND & MAINTENANCE

The stove allows the possibility to change the type of fuel used (wood/pellet) while the stove is already operating.

9.4.1 Switching from wood to pellets

To switch to automatic pellet operation when operating on wood fuel, simply hold the

button for a few

seconds:

1. the ignition LED

ZLOOVWDUWÀDVKLQJ

ZKHQWKHZRRGKDV¿QLVKHGEXUQLQJWKHVWRYHZLOOUXQDFOHDQLQJF\FOH

3. after cleaning, the stove switches to pellet operation and the ignition LED

comes on steady.

If the changeover to pellet operation has already been set, press the

button again to disable this function (

the ignition LED

ZLOOQRORQJHUÀDVK

9.4.2 Switching from pellets to wood

7RVZLWFKWRZRRG¿UHGRSHUDWLRQZKHQLQSHOOHWPRGHVLPSO\

1. open the door

2. load some logs of wood in the burn pot, making sure not to obstruct the pellet feed tube

3. close the door again

,IHQRXJKZRRGKDVEHHQORDGHGDIWHUDIHZPLQXWHVWKHVWRYHZLOODXWRPDWLFDOO\VZLWFKWRZRRG¿UHGRSHUDWLRQ

and therefore more fuel will need to be loaded manually to continue combustion.

The display will show the

symbol on the fuel menu.

When loading wood, the door needs to stay open for at least 3 seconds, so that the stove can recognise the

operation.

9.5 SWITCHING

OFF

9.5.1

6ZLWFKLQJRIILQZRRG¿UHGPRGH

7RVZLWFKWKHVWRYHRIILQZRRG¿UHGRSHUDWLQJPRGHVLPSO\VWRSORDGLQJIXHOLQWRWKH¿UHER[
:KHQWKHZRRGKDV¿QLVKHGEXUQLQJWKHVWRYHZLOOSHUIRUPDQDXWRPDWLFEXUQSRWFOHDQLQJF\FOH

Wait until the stove has completely cooled down before starting it again.

9.5.2 Switching off in pellet mode

To switch the stove off in pellet operating mode, hold the

EXWWRQIRUDIHZVHFRQGVWKHÀDPHLFRQZLOOVZLWFK

off.

:KHQWKHSHOOHWVKDYH¿QLVKHGEXUQLQJWKHVWRYHZLOOSHUIRUPDQDXWRPDWLFEXUQSRWFOHDQLQJF\FOH

Wait until the stove has completely cooled down before starting it again.

The stove should only be switched off following the procedure described above. Never switch the stove off by

unplugging it from the power supply.

9.6 OPERATION WITH ROOM THERMOSTAT (PELLET OPERATION ONLY)

When the stove is controlled by an external thermostat (or timer thermostat) the installer must have set

&RQ¿JXUDWLRQ,QWKLVFRQ¿JXUDWLRQWKHVWRYHVZLWFKHVRIIZKHQUHDFKLQJWKHH[WHUQDOWKHUPRVWDWVHWWLQJ

The stove switches on again automatically, in pellet mode, when the temperature falls below the value set on
the external thermostat (circuit closed).

2Q¿UVWLJQLWLRQRULIWKHVWRYHKDVEHHQVZLWFKHGRIIPDQXDOO\

button), the stove needs to be started

directly from the control panel.

9.7 OPERATION WITH ROOM PROBE ON THE STOVE

The stove can be switched on/off manually or in programmed mode.

The stove modulates output according to the room temperature read by the probe on the stove (that is, the stove
attempts to maintain the desired temperature while minimising fuel consumption).

If the user has enabled the “Eco-mode” function , the stove rather than modulating its output, switches
off when reaching the set temperature, and switches on again when the room temperature falls below
the delta set.

The desired room temperature can be set in the temperature menu