Palfinger ILP 25 Installation Manual Download

Page: 3 / 65

ILP 25/33 Installation Manual

Rev. 1.4

- 3 -

Table of Contents

Manual Updates ........................................................................................................................ 5

Safety Information .................................................................................................................... 6

Important Information .............................................................................................................. 7

Tools For Installation ............................................................................................................... 9

4.1

Boxed Items .................................................................................................................. 9

General View of Liftgate(s) ....................................................................................................... 10

5.1

ILP General Overview ................................................................................................... 10

5.2

Important Dimensions ................................................................................................... 11

Installation Dimensions ........................................................................................................... 12

Platform Compatibility ............................................................................................................. 14

Chassis and Body Preparation -

800mm [31.50“] Liftarm ...................................................... 15

Chassis and Body Preparation - 900mm

[35.40“] Liftarm ...................................................... 16

Gate Installation ........................................................................................................................ 17

10.1

Sill Cutouts .................................................................................................................... 17

Bed Extension Installation ....................................................................................................... 18

11.1

Bed Extension (Weld-On) ............................................................................................. 18

11.2

Bed Extension (Bolt-On) ............................................................................................... 22

Liftgate Installation (Truck) ...................................................................................................... 24

12.1

Liftgate Installation ........................................................................................................ 24

12.2

Adjusting the Platform ................................................................................................... 32

12.3

Final Steps of Installation .............................................................................................. 36

12.4

Sub-frame Installation (Optional) ................................................................................... 37

12.5

Dock Bumper Installation - Weld-On (Optional) ............................................................. 38

12.6

Dock Bumper Installation - Bolt On (Optional) ............................................................... 39

12.7

Walkramp Cradle Installation (Optional) ........................................................................ 41

Electrical Installation ................................................................................................................ 46

13.1

Electrical Wiring

– Batteries – Truck/Trailer ................................................................... 47

13.2

Cable Routing ............................................................................................................... 48

13.3

Connecting Power to Liftgate ........................................................................................ 48

13.4

Wire Crimping ............................................................................................................... 49

13.5

Circuit Breaker Installation ............................................................................................ 49

13.6

Toggle Switch Installation ............................................................................................. 50

13.7

Liftgate Shut-Off Switch ................................................................................................ 52

13.8

2-Button Hand Held Remote Control (Optional) ............................................................ 54

13.9

Electrical Schematic (Gravity Down) ............................................................................. 56

Summary of Contents for ILP 25


































































Search results

Summary of Contents for ILP 25

Reviews:

Related manuals for ILP 25

Brands by name

Popular brands

Palfinger ILP 25, Installation Manual

Search results

Summary of Contents for ILP 25

Reviews:

Related manuals for ILP 25

Brands by name

Popular brands