Palfinger ILU 40 Installation Manual & Check-Off Sheet Download

Page: 2 / 35

ABLE OF CONTENTS

Revision 1.5

- 2 -

ABLE OF CONTENTS

................................................................................................................................. 2

Safety Infromation .................................................................................................................... 5

Important Notes: ....................................................................................................................... 6

Chassis Dimension Sheets ...................................................................................................... 8

Installation Dimensions ........................................................................................................... 9

4.1

General Bed Height Ranges for ILU liftgates. ................................................................ 10

4.2

Chassis and Body Preparation ...................................................................................... 11

4.2.1

Mount frame clearance .................................................................................... 11

4.2.2

Rear sill preparation ........................................................................................ 12

Gate Installation ........................................................................................................................ 14

5.1

Slide rail bracket installation .......................................................................................... 14

5.2

Liftgate attachment ....................................................................................................... 15

5.3

Control power wiring setup ............................................................................................ 16

5.4

Platform installation ....................................................................................................... 17

5.4.1.1

Swing-door platform modifications ..................................................... 17

5.5

Lift arm Up-stop installation and rail stops setup ........................................................... 18

5.6

Control box installation .................................................................................................. 19

Gate adjusting and detailing .................................................................................................... 20

6.1

Setting B-13 lift arm sensor ........................................................................................... 20

6.2

Setting B-15 Platform sensor ........................................................................................ 21

6.3

Platform adjusting with bolts ......................................................................................... 22

Electrical Installation ................................................................................................................ 23

7.1

Breaker Installation ....................................................................................................... 23

7.2

Wiring schematic main battery power - Truck setup ...................................................... 24

7.3

Wiring schematic main battery power - Trailer setup ..................................................... 25

7.4

Trail charger installation ................................................................................................ 26

7.5

On/off switch installation ............................................................................................... 27

7.5.1

Truck setup ..................................................................................................... 27

7.5.2

Trailer setup .................................................................................................... 27

7.6

Control board wiring and connector setup ..................................................................... 28

7.7

Control board plug setup ............................................................................................... 29

7.8

Control box wiring (internal) .......................................................................................... 30

7.9

2 Button Remote Hand Control ..................................................................................... 30

Hydraulic schematic ................................................................................................................. 31

8.1

Lubrication .................................................................................................................... 32

Decal Placement ....................................................................................................................... 33

Summary of Contents for ILU 40




































Search results

Summary of Contents for ILU 40

Reviews:

Related manuals for ILU 40

Brands by name

Popular brands

Palfinger ILU 40, Installation Manual & Check-Off Sheet

Search results

Summary of Contents for ILU 40

Reviews:

Related manuals for ILU 40

Brands by name

Popular brands