background image

Document #: 4100022            Revision: F 

 

Page #: 17 of 21  

 

 

 

 
 

12. EZD OPERATING INSTRUCTIONS 

 

WARNING: EZD Clip (4100153) must be installed on the bag before 
operating EZD valve or bag can be damaged 
 

 

 

EZD stands for Easy Drain meaning a drain that allows easy transfer of fluid to and from the 
container. The typical applications include draining a container or filling a container with liquid. 
EZD operation involves relative movement of 

EZD Male port

 with respect to 

EZD Universal 

Fitment

. The Universal Female fitment always remains stationary and it is only the relative 

vertical movement of EZD Male port that allows fluid transfer through the port. The EZD is 
closed to fluid transfer when the top surface of the EZD male port is flush with the top surface of 
EZD universal fitment. When the EZD male port is pushed into the EZD universal fitment, it is 
open for fluid transfer. The 

Collar

 is used to lock the EZD valve in the preferred position (either 

open or closed) by rolling it over the fingers of the EZD universal fitment. When the collar is over 
the EZD universal fitment fingers, it prevents movement of the EZD valve and when it is rolled 
away from the finger region of the universal fitment, it allows the EZD valve to move from a 
closed to open or open to closed position. 
 

 

A necessary step to use EZD is that, an EZD CLIP be installed on the EZD universal 
fitment prior to start using it. The EZD CLIP should be mounted on universal fitment as 
shown in the image below. 

 

Summary of Contents for DU005-US






















Reviews: