background image

Model 80161A

7

Palmgren Operating Instructions and Parts Manual

Troubleshooting Chart

Motor does not run when start button
is pushed

Motor overheats

Spindle overheats

Lack of power at spindle

Cutting tool chattering

Spindle does not return to full “up”
position

Excessive backlash in lead screws

Excessive noise

Excessive play in table

1. No power to motor

2. Blown fuse on control box

3. Defective switch or contactor

1. Low voltage to motor

2. V-belts too tight

3. Too deep or too fast a cut

4. Worn contacts in contactor

1. Poor quill bearing lubrication

2. Spindle bearings too tight

3. Mill drill operated at high speeds 

for extended period

V-belts loose

1. Spindle bearings loose

2. Table is loose

3. Worn spindle bearings

4. Head clamp bolts loose

5. Too deep or too fast a cut

6. Loose workpiece

1. Poorly adjusted return spring

2. Worn return spring

Worn lead screw nuts

1. Loose spindle bearings

2. Loose motor pulley

3. Dull cutting tools

Table is loose

1. Check electrical connector and 

circuit breaker or fuse

2. Correct wiring problem and 

replace fuse

3. Replace defective parts

1. Check voltage

2. Tension belts properly

3. Reduce cut depth or speed

4. Replace contactor

1. Lubricate bearings with bearing

grease

2. Adjust bearings so that spindle 

does not bind

3. Allow mill drill to cool

Tension V-belts properly

1. Tighten bearings

2. Adjust table and saddle gibs

3. Replace bearings

4. Tighten bolts

5. Reduce cut depth or speed

6. Clamp workpiece securely

1. Increase return spring tension

2. Replace return spring

Adjust or replace lead screw nuts

1. Adjust bearings properly

2. Tighten pulley set screws

3. Replace cutting tools

Adjust table gibs properly

Symptom

Possible Cause(s)

Corrective Action

E

N
G

L

I

S

H

Summary of Contents for 80161A

































Reviews: