background image

MISO 48 FIRE PIT

Electronic Ignition 

Instal Owner's Manual

WARNING

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this 

or any other appliance.  An LP-cyllinder not connected for use shall not be stored in the 

vicinity of this or any other appliance.

WARNING:

If the information in this manual is not followed exactly, a fire or explosion may result 

causing property damage, personal injury, or loss of life.

CARBON MONOXIDE HAZARD

This appliance can produce carbon monoxide which has no odor. 

Using it in an enclosed space can kill you. 

Never use this appliance in an enclosed space such as a camper, tent, car 

or home.

DANGER

WARNING: FOR OUTDOOR USE ONLY.

Installation and service must be performed by a qualified installer, service 

agency, or gas supplier

INSTALLER: Leave this manual with the appliance. CONSUMER: Retain this manual for future reference

Burner conforms to:    ANSI Z21.97/CSA 2.41 - 2017 “Outdoor Decorative Gas Appliances”

 

 

 

CSA-2.17-2017 "Gas-fired Appliances For Use at High Altitudes"

We recommend that our fire pits be 

installed and serviced by professionals 

that are certified in the U.S. by NFI 

(National Fireplace Institute)

DANGER - FIRE OR EXPLOSION HAZARD

If you smell gas:

1. Shut off gas to the appliance. 

2. Extinguish any open flame. 

3. If odor continues, leave the area immediately.

4. After leaving the area, call your gas supplier or fire department.

Failure to follow these instructions could result in fire or explosion, which could 

cause property damage, personal injury, or death.

Summary of Contents for MISO 48


















Reviews: