EN
During Assembly
Attention
• During assembly use a soft surface below the parts to avoid scratches and damages.
Steps
Step 4:
Profile 848 should be placed on the left hand side to be connected to profile
849. Profile 848 is the one with the connector at the end.
Step 5:
After connecting profiles 816 to each other clean the connection area using a
cloth. Place the cover strip on the connection only when it is clean and dry. Press the
cover strip from one side of the connection to the other as mentioned in picture 4.
Step 8:
Profile 835 & 836 should be aligned and connected according to the illustration
on page 8 a & b. plug 23 should be inserted to each connection while the two dots on
the front of the plug should be in horizontal position for easy assembly.
Step 10:
Use part 95 as a template in order to measure the gap between posts of the
greenhouse wall and roof area.
Step 11:
Profile 841 should be placed on the right hand side. Profile 840 should be
placed on the left hand side when viewed from the front.
Step 12:
Slide the panel 566 till the end of the rail and insert it into it’s final position as
shown in illustration c .
Step 19:
Be careful to assemble the window in the position as shown on picture 20 a. profile
809 should be placed while the vent is closed to cover any gap. Ensure profile 809 is fitted
correctly as shown on picture 20 b. The lip on 809 should face toward the gutter.
Step 22:
Slide the panel 566 till the end of the rail and insert it into it’s final position as
shown in illustartion a and b.
When encountering the information icon, please refer to the relevant
assembly step for additional comments and assistance.
• Make sure the base is square by measuring the diagonals and level by using a spirit level.
• You may use silicone lubricant spray in order to help you slide the panels into the profiles.
• Do not spray the polycarbonate panels.
• Use a rubber mallet if necessary.
Step 23:
Step inside the greenhouse and turn all 23 plugs a 1/4 of a turn
clockwise.
Step 24:
Profiles 814 should be inserted from the four corners of the greenhouse,
then insert profile 815 in between them.
Step 25:
Ensure you use long screw 450 to secure the door catch 363 as shown in
illustration b.
* Please tighten all screws when completing assembly.
Note:
Firmly connect the product to a level surface immediately after completion of the
assembly.
Anchoring this product to the ground is essential to its stability and rigidity. It is required
to complete this stage in order for your warranty to be valid.
•
Screws 411 and nuts 466 are used throughout the assembly process.
•
Screws 411 are to be assembled from the outside and nuts 466 from the inside of the
greenhouse.
•
If not specified otherwise, do not fasten screws and nuts (411 & 466) for more
than 2- 3 turns.
Do not tighten them until completion of the panels’ assembly.
These 2 icons indicate if screw's tightening is required or not.
•
However, in some steps, temporary tightening of a few screws may be needed to
prevent a profile from sliding out.
466
Summary of Contents for Snap & Grow 8x8
