background image

Overall Dimensions including base (Approx)

We strongly recommend the use of work gloves during assembly . Do not attempt
to assemble the greenhouse in windy or wet conditions.

Do not touch overhead power cables with the aluminum profiles. Always wear shoes

and safety goggles when working with extruded aluminum. Dispose of all plastic

bags safely - keep them out of reach of small children. The greenhouse must be

positioned and fixed on a flat level surface. Do not lean against or push the greenhouse
during construction. Keep children away from the assembly area. Do not position

your greenhouse in an area exposed to excessive wind.

Do not attempt to assemble this greenhouse if you are tired, have taken drugs or

alcohol or if you are prone to dizzy spells. If using a step ladder or power tools ensure

that you follow the manufacturers safety advice. Hot items such as recently used grills,
blowtorches etc. must not be stored in the greenhouse. Ensure there are no hidden

pipes or cables in the ground before inserting the pegs.

This is a multi-part assembly. Allow at least 180 minutes for assembly process.

Selecting a site - choose a sunny level position away from overhanging trees. If you

are fixing your greenhouse directly to a solid concrete foundation use the pre drilled
holes in the metal base supplied. The component parts should be checked and laid

out close at hand. Keep all small parts (screws etc.) in a bowl so they do not get lost.

Keep roof clear of snow and leaves.

When your greenhouse needs to be cleaned, use a mild detergent solution and rinse

with cold clean water. DO NOT use acetone, abrasive cleaners or other special

detergents to clean the clear panels.
Replacement parts - contact Customers service helpline at:

For additional information please visit our web site: www.palram.com

Tape measure

Work gloves

Crosshead screwdriver
Bradaw

Drill
2mm metal drill bit

Scissors

Step ladder
Spirit level

If help is required seek professional advice whithin store.

LEAN-TO

Greenhouse

ASSEMBL Y IN STRUC TIO NS

129L x 71W x 165H CM

Keep these instructions in a safe place for future reference.

You must read these instructions carefully before you start to assemble
this greenhouse. Please carry out the steps in the order set out in these
instructions.

Do not tighten the screws of the Greenhouse until completing on the
assembly of the panels.

I MP O R TA N T

SAFETY ADVICE

GENERAL ADVICE

CARE & MAINTENACE

TOOLS & EQUIPMENT

Version  #3

Summary of Contents for 700492















Reviews: