Palram PATIO COVER EZ LINK, Manual

Steps: 

Step 2:

 To assemble the rear profile please refer to the patio cover assembly manual at the stage of 

"

holes marking

" as:

Feria

Tuscany

Olympia

Sierra

Joya

Carnival

3x3 - 

Step

 7

3x3 - 

Step

 7

3x3 - 

Step

 5

All sizes

Step

 5

All sizes

Step

 6

3x3 - 

Step

 6

3x4.25 - 

Step

 6 3x4.25 - 

Step

 9 3x4.25 - 

Step

 7

3x4.25 - 

Step

 5

3x5.46 - 

Step

 9 3x5.46 - 

Step

 9 3x5.46 - 

Step

 7

-

4x4.25 - 

Step

 12

-

-

-

For 

fixation to the wall

, return to step 2.

Step 3:  

connect part 

8303

 (

drawings a,b

) and than return to the patio cover assembly manual as follow: 

Feria

Tuscany

Olympia

Sierra

Joya

Carnival

3x3 - 

Step

 8

3x3 - 

Step 

8

3x3 - 

Step 

6

2.3x2.3 - 

Step 

7

3x3 - 

Step

 7

3x3 - 

Step

 10

3x4.25 - 

Step

 13 3x4.25 - 

Step

 13 3x4.25 - 

Step

 11 3x3 - 

Step

 6

3x4.25 - 

Step

 10 3x4.25 - 

Step

 9

3x5.46 -

Step 

13 3x5.46 - 

Step 

13 3x5.46 - 

Step

 11 3x4.25 - 

Step 

9 3x5.46 - 

Step

 10

-

4x4.25 -

Step 

16

-

-

3x5.46 - 

Step 

9

-

-

After completion, perform 

drawing c

 at this step.

Step 4

: In all relevant patio cover sizes, you may choose either of these 2 assembly options:

Option 1 

(Steps 4+5+6+9+10+11+12) - assembling all posts supplied.

Option 2

 (Steps 4+7+8+9+10+11+12) - Whenever you are using this EZ Link Kit you may give up using 

one leg.

Step 6 (Option 1) :

 make sure the distance between the post and the connection point does not exceed 

60 cm / 23.6 inch. The Maximum distance between the posts may not exceed 120 cm / 47.2 inch.

Step 10: 

before performing this stage, return to the patio cover assembly manual at the stage of  

"assembling the roof system"

 as follow:

Feria

Tuscany

Olympia

Sierra

Joya

Carnival

3x3 - 

Step

 15

3x3 - 

Step 

14

3x3 -

Step 

11 2.3x2.3 - 

Step

 12 3x3 - 

Step 

13

3x3 - 

Step

 18

3x4.25 - 

Step

 22 3x4.25 - 

Step

 20 3x4.25 - 

Step

 17 3x3 - 

Step

 11 3x4.25 - 

Step 

17 3x4.25 - 

Step

 16

3x5.46 - 

Step 

21 3x5.46 - 20 

Step

3x5.46 -

Step

 17 3x4.25 -

Step 

15 3x5.46 -

Step

 17

-

4x4.25 - 

Step 

26

-

-

3x5.46 - 

Step 

15

-

-

Step 12: 

Tightening the bolts is done from the inner part. Spread silicone follow the connection (a,b).

 Pay attention:

 while installing the kit, alignment with original patio cover is important.

 Tighten all screws when completing assembly. 

    When encountering the information icon, please refer to the relevant  

assembly step for additional comments and assistance.

  This icon indicates that the installer should be inside the product.

Please read these instructions carefully before you start to 

assemble this product.

Please carry out the steps in the order set out in these instructions.

Keep these instructions in a safe place for future reference.

Safety

•  Some parts may have sharp edges. Please be careful when handling components.
•  Always wear gloves, eye protection, and long sleeves when assembling or performing  

any maintenance on your product.

•  To prevent injuries, do not allow children to play under the product during assembly.

Before Assembly

•  This product is suitable for Palram’s Patio Covers range 
•  It is highly recommended to be assisted by a second person in some steps.
•  Sort the parts and check according to the contents parts list.
•  Prior to the installation, some parts of the Patio cover need to be  

dismanteld, it is recommend to keep them in a safe place for future use.

•  Periodically check the kit’s components to assure that it remains stable.

•  Note

: Use only the parts registered in the content list, which are compatible  

with your Patio Cover›s gutter (7999 & 8119), some parts may be surplus.

During Assembly

In case that you already own Palram Patio cover it is necessary to  
dismantle parts as described in

 Step 1

 in the kit assembly manual.

EN

74803_20.09_V4.1 _MV

-5