Palram PLANT INN TWIN WALL, Manual

Customer Service

For assistance with assembly, replacement parts or any other additional information 
please log onto our website or call our customer service line (number is on the title page). 
www.palramapplications.com

Safety advice

•  It is of utmost importance to assemble all of the parts according to the directions.  

Do not skip any step.

•  We strongly recommend using work gloves during assembly. 
•  Always wear shoes and safety goggles when working with extruded aluminium.
•  If using a step ladder or power tools ensure that you follow the manufacturer›s safety advice.
•  Do not  touch overhead power cables with the aluminium profiles. 
•  Do not attempt to assemble the product in windy or wet conditions.
•  Dispose of all plastic bags safely keep them out of reach of small children.
•  Keep children away from the assembly area.
•  Do not lean against or push the product during construction. 
•  Do not position your product in an area exposed to excessive wind.
•  Do not attempt to assemble this product if you are tired, have taken drugs or alcohol or if you are 

prone to dizzy spell.

•  From safety reasons always use the lockers for each position (close, open, ventilation, storage) as shown 

in step 33 Hot items such as recently used grills, blowtorches etc. must not be stored in the product. 
Ensure there are no hidden pipes or cables in the ground before inserting the pegs.

•  This product was designed to be used mainly as a growhouse.

Care & Maintenance

When your product needs to be cleaned, use a mild detergent solution and rinse with cold clean water. 
DO NOT use acetone, abrasive cleaners or other special detergents to clean the clear panels.

Tools & Equipment

•  Tape measure
•  Work gloves
•  Lubricant
•  Phillips head screwdriver
•  Step ladder
•  Drill bit
•  Large hammer
•  Spanner
•  Sïlicon spray

IMPORTANT
Please read these instructions carefully before you start to assemble this product.
Keep these instructions in a safe place for future reference.

EN

Before Assembly

This is a multi-part assembly best achieved by two people.  
Allow at least half a day for assembly process.
Selecting a site - the product must be assembled, positioned and fixed  
on a flat level surface.
Choose a sunny position away from overhanging trees. 
Take out all components parts of the packages. Sort the parts and  
check against the contents parts list.
During assembly parts should be laid out close at hand. Keep all small  
parts (screws etc.) in a bowl so they do not get lost.

Notice:

•  All panels with the stamped words “THIS SIDE OUT” must be facing out to create  

full UV protection. Remove plastic sticker as panels are locked in place.

Step 4(c) :

 Make sure screws stay loose.

Step 5 :

  If trays are dropping down when filled with soil, push trays’ frame up  

and  tight these screws again on their original position.

Step 7 :

 Make sure screws are strongly tightened.

Step 25 :

 make sure profiles are inserted all the way till the end into plastic connector.

Steps 29 :

 If lid does not located correctly on the frame it will not closed and opened 

properly. Try re-checking 

Step 20

 (measure) and 

Step 25 

(insert profiles all the way).

Tighten all screws when completing assembly.

After assembly

This product’s ground fixing is based on soil weight. When trays are empty it should  
be kept from winds. There for we are strongly recommending fixing  
the product directly to a solid concrete foundation.

82760B_21.04_V2_MV_8.2

•   Screws 411 and nuts 412 are used thruoghout the assembly process. 
•   Screws 411 are to be assembled from the outside and nuts 412 from the inside of the 

greenhouse.   

•   Do not fasten screws and nuts (411 & 412) more than 23- turns only. Do not tighten  

them until completion of the panels’ assembly, if not specified otherwise.

•   However, in some steps, temporary tightening of a few screws may be needed to 

prevent a profile from falling.