background image

2. Safety

2.1 Safety Instructions (A+B)

A-Electrical Connection Safety

Check whether your appliance and power cord are damaged before operating your
appliance.

Check whether there is any crack, disjoint or scratch on the filament (heating tube). If
any, contact with your authorized technical service.

If you appliance or power cord is damaged, do not operate your appliance and return
it to your technical service.

Make sure that the main electricity circuit is 220-240V and 110-120V, 50-60Hz and
the connection is fused.

Check the safety of the network. The fuse must be 25A.

Do not use your infrared heater together with another appliance plugged to the same
multiple sockets or connected to the same fuse.

Use your appliance with a properly earthed plug.

The earthed plug must fall outside heating field and hot surface.

The power cord must not be left on or around the frame of your infrared appliance.

Unplug your appliance when you won’t operate it for a long term or will conduct
cleaning or maintenance.

The damaged heater glass must be exchanged.

If the cable of the heater should be damaged, this may be replaced only by the
authorized service.

If has to be notified that the mounting in the bath must be so that the persons in the
bath can not reach the controls.

It has to be notified that the product has to be installed at a dry location and may not
be wet.

B-Safe distances required for installation on the wall, high temperature and fire protection

Attention! The appliance must only be operated in a horizontal position with
max±15°slope. In case of operations in angels larger than 5°in horizontal position or
of vertical operations, the heating loop wire may fall into disuse shortly.

Never install your appliance on a combustible surface (carton etc.)
The distance of your appliance from the ground is to min 1.8 m (6 feet).

The distance of your appliance from the ceiling is to be min 0.7 m (2.5 feet).

The distance of your appliance from the living beings is to be min 1 m (3.5 feet).

The distance of heating area of your appliance from the materials such as wood,
carton, cloth etc., must be min 1 m (3.5 feet).

Do not cover your appliance and do not hang any clothing over the heater or do not
place any clothing on or near the appliance.

Do not stick anything into the protective grid.

Summary of Contents for JHB-1500R

















Reviews: