background image

1

- MAX

®

7500-PRO

1

- RJ-11 telephone cable

2

- Coax cables for 

satellite TV,  cable TV,
and/or antennas

- Rack ears w/ screws for rack 

mounting option 

Important Safety Instructions......................................1

Introduction.................................................................2

Connection Diagram....................................................3

Feature Overview.........................................................4 

Feature Details

Analog Voltmeter & Ammeter.................................5

Convenience Outlet................................................5

Diagnostic Lights...................................................5

Sequential Startup/Shutdown................................5

High-Current Outlet Bank......................................5

Isolated/Regulated Outlet Bank..............................5

Regulated Outlet Banks 1 and 2.............................6

Convenience Lamp................................................6

Voltage Sense Triggers.........................................6

Isolation Transformer Circuit Breaker.....................6

Coaxial Line Protection..........................................6

Telephone Line Protection......................................7

AC Surge Protection..............................................7

AVM (Automatic Voltage Monitoring) Protection............7

Automatic Over & Under Voltage Protection..........7

Technical Specifications...............................................8

RS-232 Command Specification...........9, 10, 11, 12, 13

Troubleshooting........................................................14

Warranties.................................................................15

TABLE OF CONTENTS

USA & Canada (800) 472-5555  •   (707) 283-5900  •  Fax (707) 283-5901

1

- LED convenience lamp

1

- IEC 320, 120V/15A 

detachable power cord

1

- Rack mount blank

BEFORE YOU BEGIN

In addition to this owner’s manual, items included with the MAX

®

7500-PRO package are:

Please verify that you have received all these items. If not, contact Panamax.

M7500-PRO

POWER FILTRA

TION AND REGULA

TION ACTIVE                                       HIGH CURRENT

 GROUND
ISOLATION

ACTIVE

BANK 1 ON       BANK 2 ON       BANK 3 ON       BANK 4 ON          BANK 5              BANK 5 

 HC 1 ON           HC 2 ON

BRIGHTNESS 

PRESS: 

METER SELECT

Home Theater P

ower Management

AUTO

If the M7500-PRO is installed in a rack, this “blank” must be installed
directly below the M7500-PRO to ensure proper ventilation.

Summary of Contents for MAX 7500-PRO


















Reviews: