16
About the Signals to Input to GENLOCK IN Connector
Supply the following signals to the GENLOCK IN connector, as a GENLOCK input signal to this unit, in accordance with the
video format used.
Video may be disrupted if any other signals are supplied.
<Note>
When using the unit in HD mode, input the HD 3-value SYNC signal or black burst signal. When using the SD mode, input the
black burst signal. When the SD 2-value SYNC signal without a burst signal is supplied, GENLOCK does not work.
About the RET Signal
The RET signal input to this unit can be transferred to the camera adapter.
When the video format of the camera recorder is HD format, the video signal supplied to the RET IN SDI connector and the
RET IN VIDEO connector can be transferred to the camera adapter. When the video format of the camera recorder is SD
format, either of the video signals supplied to the RET IN SDI connector or the RET IN VIDEO connector can be transferred to
the camera adapter.
The signal output to the VF OUT connector (D-Sub connector) of the camera adapter can be switched with the RET signal
selection switch at the rear panel of this unit.
*1 When the video format of the camera recorder is HD format, SD SDI signals cannot be transmitted.
*2 When the video format of the camera recorder is SD format, HD SDI signals cannot be transmitted.
Video format of the camera recorder
Signal to be supplied to the GENLOCK IN connector (analog signal)
1080/59.94i
When HD SYNC is supplied
1080/59.94i, 3-value SYNC
When SD SYNC is supplied
480/59.94i, black burst signal (SYNC + burst)
1080/23.98PsF
When HD SYNC is supplied
1080/23.98PsF, 3-value SYNC
When SD SYNC is supplied
Not supported
1080/50i
When HD SYNC is supplied
1080/50i, 3-value SYNC
When SD SYNC is supplied
576/50i, black burst signal (SYNC + burst)
1080/24PsF
When HD SYNC is supplied
1080/24PsF, 3-value SYNC
When SD SYNC is supplied
Not supported
720/59.94P
When HD SYNC is supplied
720/59.94P, 3-value SYNC
When SD SYNC is supplied
480/59.94i, black burst signal (SYNC + burst)
720/60P
When HD SYNC is supplied
720/60P, 3-value SYNC
When SD SYNC is supplied
Not supported
720/50P
When HD SYNC is supplied
720/50P, 3-value SYNC
When SD SYNC is supplied
576/50i, black burst signal (SYNC + burst)
480/59.94i
When HD SYNC is supplied
Not supported
When SD SYNC is supplied
480/59.94i, black burst signal (SYNC + burst)
576/50i
When HD SYNC is supplied
Not supported
When SD SYNC is supplied
576/50i, black burst signal (SYNC + burst)
Video format of the
camera recorder
Input signal of the AG-BS300P/E
Output signal to the AG-CA300G
Input signal
connector name
Input signal
switch at the rear
VF OUT connector
(D-Sub)
RET OUT connector
(BNC)
HD
RET IN SDI
HD SDl (signal A)
SDI
HD component
(signal A)
Composite (signal B)
RET IN VIDEO
Composite (signal B)
RET IN SDI
HD SDl (signal A)
VIDEO
SD component
(signal B)
RET IN VIDEO
Composite (signal B)
RET IN SDI
SD SDl (signal C)*
1
SDI
Signal is not output
RET IN VIDEO
Composite (signal B)
RET IN SDI
SD SDl (signal C)*
1
VIDEO
SD component
(signal B)
RET IN VIDEO
Composite (signal B)
SD
RET IN SDI
SD SDl (signal A)
SDI
SD component
(signal A)
Composite (signal A)
RET IN VIDEO
Composite (signal B)
RET IN SDI
SD SDl (signal A)
VIDEO
SD component
(signal B)
Composite (signal B)
RET IN VIDEO
Composite (signal B)
RET IN SDI
HD SDl (signal C)*
2
SDI
Signal is not output
RET IN VIDEO
Composite (signal B)
RET IN SDI
HD SDl (signal C)*
2
VIDEO
SD component
(signal B)
RET IN VIDEO
Composite (signal B)
AG-BS300P_E(VQT2H41)_E.book 16 ページ ２００９年１０月２３日 金曜日 午後６時８分
