Chapter 7 Output and Screen Display
—
Screen status display
- 161 -
6
Remaining recording capacity and status of the memory card
Displays the remaining recording capacity and status of the memory card in card slot 1 or card slot 2.
≥
[0min] to [999min]:
Remaining recording capacity (999 minutes or more is displayed as [999min])
j
The display will flash when the remaining recording capacity becomes 2 minutes or less.
j
The recording capacity available for simultaneous recording (recording capacity for the memory card of the 2 memory cards with less recording
capacity) is displayed when simultaneous recording is performed.
≥
[WP]:
Write protected (the write protection switch of the memory card is set to the LOCK side)
≥
[END]:
No remaining recording capacity (no remaining recording capacity on the memory card)
≥
[ERR]:
A memory card that cannot record is inserted (the card is recognized but cannot record due to a format error, a card other than a memory
card being inserted, etc.)
≥
[!SDXC]:
An SDXC memory card is not inserted in MOV recording/MP4 recording
≥
(No display):
It is in one of the following conditions.
j
A memory card has not been inserted.
j
The memory card cannot be recognized.
j
(For the
)
The [NETWORK] menu
→
[NETWORK FUNC]
→
[NDI|HX] is set.
7
External equipment recording operation control status (<SDI OUT>/<HDMI> terminal)
Displays the control status of the recording start and recording stop on the external equipment connected to the <SDI OUT> terminal and the
<HDMI> terminal.
≥
[
SDI]
*1
:
Recording instruction is output to the output from the <SDI OUT> terminal.
≥
[SDI]
*1
:
Pause instruction is output to the output from the <SDI OUT> terminal.
≥
[
HDMI]:
Recording instruction is output to the output from the <HDMI> terminal.
≥
[HDMI]:
Pause instruction is output to the output from the <HDMI> terminal.
8
Special recording function
Displays the status of special recording function.
≥
[INTRVL]:
The interval recording is stopped.
≥
[I-REC]:
The interval recording is in progress. (Displayed in red)
9
2-slot function
Displays the setting status of the recording function using 2 memory cards.
It is displayed with a slanted line if it is in a condition that cannot perform 2-slot recording even if each function is enabled.
≥
[RELAY]:
When the relay recording is enabled
≥
[SIMUL]:
When the simultaneous recording is enabled
≥
[BACKGR]:
When the background recording is enabled
≥
(No display):
During standard recording
j
(For the
)
When set to the [NETWORK] menu
→
[NETWORK FUNC]
→
[NDI|HX], [NDI|HX] is displayed
10
Flash band compensation function
≥
[FBC]:
Displayed when the flash band compensation function is operating.
11
Streaming status
Displays the streaming status.
≥
:
When the unit is connected to a device to receive the streaming video, and the streaming video is distributed
≥
(flashing):
When the unit is being connected to a device to receive the streaming video
≥
:
When the streaming function is enabled, it is in condition to operate properly, and the streaming video is not distributed
≥
:
When there is an error in the streaming function and cannot operate
≥
(No display):
When the streaming function is disabled
12
Dynamic range stretcher function
≥
[DRS]:
Displays when the dynamic range stretcher function is working.
13
Connection status of the wireless LAN/wired LAN
Displays the connection status of the wireless LAN or wired LAN.
≥
:
When set to the wireless LAN and the ROP is not connected
≥
:
When set to the wireless LAN and the ROP is connected
≥
:
When set to the wireless LAN and the wireless LAN is not operating properly
≥
*2
:
When set to the wired LAN and the ROP is not connected
≥
*2
:
When set to the wired LAN and the ROP is connected
≥
*2
:
When set to the wired LAN and the wired LAN is not operating properly
≥
(No display):
When both the wireless LAN and the wired LAN are disabled
14
Power status
:
Displays the remaining battery level while powered with the battery. (The battery status display will change as
→
→
→
→
→
while the remaining battery level gets lower. It will flash in red when the remaining battery level is zero.)
:
Displayed when powered with the AC adaptor.
15
Audio level meter
Displays the audio level meter.
A white border is displayed in the position of the recording base level (12 dB).
≥
:
Displayed when audio cannot be recorded. (When super slow is enabled, etc.)
16
Luminance of Y GET
Displays the luminance level in 0% through 109% when the Y GET function is operating.
17
Gain
Displays the gain value.
≥
[AGC]:
Displayed when the auto gain control is operating.
≥
[SG]:
Displayed when [SUPER GAIN] is working.
≥
[SG
i
]:
Displayed when [SUPER GAIN
i
] is working.
CX10
CX10
