Panasonic AG-DVC30P Service Manual Download | Manualshive

Page: 102 / 413

background image

ELE-18

6. CAMERA ADJUSTMENT PROCEDURE

Be sure to save the Camera adjustment data into the Personal Computer, before performing adjustment.
Perform all PC-EVR adjustments, by referring to procedures on PC screen.

6-1. Iris Hall Amp Adjustment (AUTO)

This adjustment is automatically executed.
1. Open the

“Camera adjustment menu”

. Please

2. Select

“2. Iris Hall Amp adjustment (Auto)”

in the Camera adjustment menu, and then press the

“Enter”

key.

3. Set to CAMERA mode in camera recorder follow the message

“Auto / Manually set to CAMERA mode.”

, and

then press the

“Enter”

key.

When adjustment is finished, message

“Completed!”

appears and numerical value is

changed

“00”

.

The program goes to Camera adjustment menu
automatically.

PRESS ENTER KEY.

PRESS ENTER KEY, then adjustment is
started.

«
...
100
101
102
103
104
...
»

Summary of Contents for AG-DVC30P






























































































































































































































































































































































































































Reviews:

No comments

Related manuals for AG-DVC30P

Brand: Night Owl Pages: 9

Brand: Vivitar Pages: 37

Brand: Sanyo Pages: 2

Brand: Argus Pages: 1

Brand: Sony Pages: 2

Brand: Sigrand Pages: 59

Brand: LABS Pages: 42

Brand: Kodak Pages: 2

Brand: Hasbro Pages: 9

Brand: Gator Pages: 19

Brand: Canon Pages: 162

Brand: Panasonic Pages: 220

6108 - Cell Phone - GSM

Brand: Nokia Pages: 110

Brand: Panasonic Pages: 102

Brand: Panasonic Pages: 88

Brand: Panasonic Pages: 124

Brand: Panasonic Pages: 80

Brand: Panasonic Pages: 108

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands