25
Basic Oper
ation
NOTE
The same input sources are assigned to the A/PROG bus and
the B/PRESET bus.
It is impossible to assign different sources to each bus.
9OUCANCHECKTHEINPUTSOURCECURRENTLYASSIGNEDTOTHE
SELECTEDNUMBERONTHEMONITORCONNECTEDTOTHE3$)/54
PVW connector.
To set the video and audio input sources
Video and sound are allocated to input source numbers 1
TOONTHE!UDIO6IDEO)NPUT3OURCE3ETTINGSCREEN
Allocate the video input sources named [V S-1], [V S-2],
s
[V S-3], and [V S-4] to any of numbers 1 to 8, specifying
the video input sources to use.
Allocate the audio input sources named [A S-1], [A S-2],
s
[A S-3], and [A S-4] to any of numbers 1 to 8, specifying
the audio input sources to use.
)TISALSOPOSSIBLETOMAKESETTINGSTOESTABLISHTHE
correspondence between video input sources and audio
INPUTSOURCES3EEh4OASSOCIATEVIDEOINPUTWITHAUDIO
INPUTv
PAGE
To allocate video and audio to the selected
number
Select one of the video input sources [V S-1], [V S-2],
[V S-3], and [V S-4] using the rotary 2 control.
3ELECTONEOFTHEVIDEO;3$)=;($-)=;6)$%/=AND;$6))=
3$)INPUT($-)INPUTCOMPOSITEINPUTAND$6)INPUT AS
the video input sources [V S-1] to [V S-4] using the rotary 3
control.
Each input type supports the signal formats as shown
below.
Input
Format
3$)
All formats
($-)
PPII
0S&WHEN;$=ISSETTO;-/$%=OR
;-/$%=
6)$%/
II
$6))
8'!78'!38'!PP
Select one of the audio input sources [A S-1], [A S-2],
;!3=AND;!3=3$)INPUTTO USINGTHEROTARY
control.
3ELECTONEOFTHEAUDIO;3$)=;($-)=AND;!.!,/'=3$)
INPUT($-)INPUTANDANALOGINPUT ASTHEAUDIOINPUT
sources [A S-1] to [A S-4] using the rotary 5 control.
NOTE
If the system format is set to SD (
s
page 19), [HDMI] cannot
be selected. If the system format is set to HD, [VIDEO]
cannot be selected.
You cannot set the combinations of video and audio
s
input sources shown in the table below. (The settings are
automatically changed to available values.)
When the video input is HDMI, only two channels of audio
sources can be input.
Video Input
Audio Input
3$)
3$)3$)3$)($-)($-)
3$)
3$)3$)3$)($-)($-)
3$)
3$)3$)3$)($-)($-)
3$)
3$)3$)3$)($-)($-)
($-)
3$)3$)3$)3$)($-)
($-)
3$)3$)3$)3$)($-)
$6))
3$)3$)3$)3$)($-)($-)
To fix the settings and return to the [AUDIO
VIDEO] screen
Press the
KEY
4ORETURNTOTHE;!5$)/6)$%/=SCREENWITHOUTlXINGTHE
settings, press the
KEYWHILEHOLDINGDOWNTHE3()&4
KEY
NOTE
If other menu screen is displayed without fixing of the settings
on the Audio/Video Input Source Setting screen, those settings
are revoked and not applied.
To associate video input with audio input
1
Set [INPUT] to [V-LINK] using the rotary 2
control, and press the key.
2
When the message [OK?] appears, press the
key again.
Audio input sources corresponding to the video
input sources assigned to 1 to 8 are set.
To cancel the setting, press the key while
holding the SHIFT key.
The display returns to the [SETUP] menu screen.
NOTE
For input settings in 3D mode, it is possible to select only
combinations of image input sources and audio input sources
which are associated with each other. When 3D mode is set to
other than [OFF], [V-LINK] does not appear as the setting item.
To use the factory default settings
1
Set [INPUT] to [DEFAULT] using the rotary 2
control, and press the key.
2
When the message [OK?] appears, press the
key again.
Summary of Contents for AG-HMX100P
Page 47: ...MEMO 47 ...
