Panasonic AG-HMX100P, Operating Instructions Manual

26

Basic Oper

ation

To cancel the setting, press the   key while 
holding the SHIFT key.

The display returns to the [SETUP] menu screen.

To set the output of the AUX connector

4HE!58CONNECTOROFTHE3$)/54CONNECTORSCANOUTPUT
THEINPUTSOURCEASISREGARDLESSOFTHE;!5$)/6)$%/=

settings.

Operate the rotary 4 control to select the input terminal to 
which the source you want to output is connected.
If [PGM], [PVW], or [M VIEW] is selected, the same source 
as that of the PGM, PVW, or MULTI VIEW connector is also 

OUTPUTFROMTHE!58CONNECTOR



 NOTE

The [AUX] settings are saved in different memory for the 

s

respective cases in which the system format setting is 
SD (



 page 19) and HD (including 3D mode). The saved 

settings are called according to the system format when it is 
switched.
No DVI-I input source can be selected. 

s

To set the input source for the waveform 
monitor (WFM)

Operate the rotary 5 control to select the input source for 
the waveform monitor with multi-view output.



 NOTE

The [WFM] setting values are saved separately for the 
respective cases in which the system format setting is HD 
(including 3D mode) and SD. The saved values are called 
according to the system format set in the [VIDEO FORMAT] 
submenu of the [SETUP] menu.

Setting the Video Format 
[VIDEO FORMAT] 

)TISNECESSARYTOMAKETHESETTINGSFORVIDEOSIGNALSOUTPUT
FROMTHEUNITVIDEOFORMATSETTING ACCORDINGTOTHELOCATION

where this unit is used and the video output method. 

To set the video format for the entire system in this unit 

HEREINAFTERCALLEDhSYSTEMFORMATv USETHE;6)$%/
&/2-!4=SUBMENUOFTHE;3%450=MENU

If the system format is changed, the current settings are 

INITIALIZEDTOCLEARTHESETTINGSINTHE;).46)$%/=MENU

(



PAGE ANDTHETITLEMEMORYSETTING



PAGE

Rotary 1

Rotary 2

Rotary 3

Rotary 4

Rotary 5

0

7.5

4:3

16:9

480/59i

576/50i

720/50p

720/59p

1080/50i

1080/59i

HDMI

VIDEO 

1080/59i

7.5

SET UP 

FORMAT

16:9

ASPECT 

AG-HMX100P

Rotary 1

Rotary 2

Rotary 3

Rotary 4

Rotary 5

0

7.5

4:3

16:9

480/59i

576/50i

720/50p

720/59p

1080/50i

1080/59i

HDMI

VIDEO 

1080/59i

0

SET UP 

FORMAT

16:9

ASPECT 

AG-HMX100E

To select the aspect ratio

7HENIORIHASBEENSELECTEDWITHTHEROTARY

2 control, [4:3] or [16:9] can be selected with the rotary 3 
control.
When the system format in which the aspect ratio cannot 
be set has been selected, [---] appears.
The factory default setting is [4:3].

To select setup level (black level)

7HENIHASBEENSELECTEDWITHTHEROTARYCONTROL

[0] or [7.5] can be selected with the rotary 4 control.
When the system format in which the setup level cannot be 
specified has been selected, [--] appears.

4HEFACTORYDEFAULTIS;=!'(-80 OR;=
!'(-8%

Changing the system format

1

Select the system format that you want to set 
using the rotary 2 control.

If a setting value differing from the current system 

FORMATISSELECTEDASTERISK ISADDEDTOTHE

current setting value.

2

Press the   key.

3

When the message [OK?] appears, press the 

 key again.

When the 

KEYISPRESSEDTOlXTHESELECTION

because the signal format switching is performed, 
the operation of this unit is disabled for several 
seconds.

4

When the message “TURN POWER OFF” 
appears, turn off the power and restart the unit.



 NOTE

If other menu screen is displayed without fixing of the settings 

s

on this screen, those settings are revoked and not applied.  
When 3D mode is set to other than [OFF], “--” appears and 
the system format cannot be changed.
If [HDMI] is selected, the HDMI input signal is output as 

s

is from the DVI-D OUT connector, disabling the AV mixer 
functions including video switching effects.