Panasonic AG-HMX100P, Operating Instructions Manual

27

Basic Oper

ation

When the 3D mode is [OFF] (

s



 page Vol.2-25), the system 

format of this unit is the one set in the [VIDEO FORMAT] 
submenu of the [SETUP] menu. When the 3D mode is other 
than [OFF], the system format of this unit is the one set 
under the [3DFORMAT] item in the [3D] submenu of the 
[SETUP] menu.

Setting the Bus [BUS]

The [BUS] submenu of the [SETUP] menu is used to set the 
output method of this unit to either of the following: 

AB bus system: Switches between video A and video B.

s

0ROGRAM0RESETSYSTEM3WITCHESBETWEENPROGRAM

s

OUTPUTBASEVIDEO ANDPRESETOUTPUTVIDEOUSEDAS
EFFECTS

7HENTHE0ROGRAM0RESETSYSTEMISSELECTEDTHE!02/'

bus source selector button corresponding to the source 
used for the transition pattern and output from a PGM 

CONNECTORISNECESSARILYLIGHTEDORmASHES4HUSANINPUT

source that you want to display next can be selected only 

WITHTHE"02%3%4BUSSOURCESELECTORBUTTONS



 For more information about the input source selection 

operation, see page 33.

Rotary 1

Rotary 2

Rotary 3

Rotary 4

Rotary 5

AB

PRG/PRE

TYPE

BUS

AB

3ET;490%=TO;!"=!"BUSSYSTEM OR;02'02%=
0ROGRAM0RESETSYSTEM USINGTHEROTARYCONTROL

The factory default setting is [AB].

Setting Audio Channels [AUDIO CH] 

4HE;!5$)/#(=SUBMENUOFTHE;3%450=MENUISUSED
TOSELECT,CHANNELOR2CHANNELOFTHISUNITFOREACHAUDIO
CHANNELOFTHESELECTED3$)INPUTSOURCE
7HENTHESYSTEMFORMATIS($



PAGE AUDIO

channels 1 to 8 can be assigned. When the system format 

IS3$AUDIOCHANNELSTOCANBEASSIGNED

Rotary 1

Rotary 2

Rotary 3

Rotary 4

Rotary 5

1-8 (1-4)

1-8 (1-4)

OFF

ON

SDI1

SDI2

SDI3

SDI4

CH

CH

AUDIO

SDI1

1

2

ON

L-CH

R-CH 

OSD

1

Set [CH] to one of [SDI1], [SDI2], [SDI3], or 
[SDI4] (SDI inputs 1 to 4) using the rotary 2 
control.

2

Use the rotary 3 control to select the audio 
input (of the SDI input selected in Step 1) which 
you want to assign the L channel by setting 
[L-CH] to the desired audio input number. 

3

Use the rotary 4 control to select the audio 
input (of the SDI input selected in Step 1) which 
you want to assign the R channel by setting 
[R-CH] to the desired audio input number.

4

Repeat Steps 1 to 3 to assign each audio 
input of SDI inputs 1 to 4 to the L channel or R 
channel.



 NOTE

The set channel is stored in memory separately between the 
cases in which the system format is SD and HD (



 page 19), 

and is called according to the format when the system format 
is changed.

To hide the audio level meter during 
multi-view output

3ET;/3$=TO;/&&=USINGTHEROTARYCONTROL

The factory default setting is [ON], in which the audio level 
meter is displayed when the multi-view output is monitored.

Setting the Audio Faders 
[AUDIO FADER]

4HEAUDIOINPUTLEVELISADJUSTEDWITHTHE3/52#%
FADERSAUDIOFADERS

When adjusting the audio level of input sources 5 to 8, 
operate the corresponding fader while holding down the 

3()&4KEY

/PERATETHE!58FADERTOADJUSTTHE!58INPUTLEVELAND

the MIC fader to adjust the MIC input level.

4HEOPERATIONOFTHEAUDIOFADERS!58FADERAND-)#
FADERCANBESETFROMTHE;!5$)/&!$%2=SUBMENUOFTHE

[SETUP] menu. 

Rotary 1

Rotary 2

Rotary 3

Rotary 4

Rotary 5

PAIR

SEPA.

CP PAIR

BUS SEP1

BUS SEP2

12 PAIR

12 SEPA.

FADER

SOURCE

AUDIO

BUS SEP1

PAIR

AUX/MIC