32
Basic Oper
ation
3
Set [FRAME] to the number of frames to
preview using the rotary 3 control.
To preview the movie, select a value equivalent
to or smaller than the number of frames of the
movie.
4
To preview the still picture, select [FRAME]
(frame display) or [FIELD] (field display) using
the rotary 4 control.
To preview the movie, select [REPEAT] (repeat
playback) or [ONCE] (only-once playback)
using the rotary 4 control.
5
Press the key.
$URINGSTILLPICTUREPREVIEWTHESTILLPICTUREONTHE
page selected in above Step 2 is displayed.
$URINGMOVIEPREVIEWTHEMOVIECONTAINSFRAMES
the number of which is selected in Step 2 is played
BACK
NOTE
Upon save of a still picture or movie, set [MODE] to [EXIT] to
s
prevent the saved data from being overwritten.
If you select [EXIT] during playback of a saved movie and
s
press the
key, the image of the last frame is displayed
and the playback of the movie stops.
Even if other internal video (back matte or color bar) is
s
selected in the [INT VIDEO] menu, [MEMORY] can be
selected again to call the previously saved still picture or
movie. However, the saved still pictures and movies are
deleted when the power is turned off.
To start/stop playback of a movie without
using the [INT VIDEO] menu
1
Press the . (period) key while holding the SHIFT
key.
2
Start playback in the confirmed playback
method for internal video.
3
To stop playback, press the . (period) key while
holding the SHIFT key again.
Using Video Input from PC [PC1]
6IDEOCANBEINPUTFROM0#TOTHISUNITVIATHE$6))).
connector.
For using video created on PC, it is necessary to allocate
THE$6))INPUTTOANINPUTSOURCENUMBERINTHE;!5$)/
6)$%/=SUBMENUOFTHE;3%450=MENUINADVANCE
(
PAGE
The source input from PC is set from the [PC1] submenu of
the [SETUP] menu.
Rotary 1
Rotary 2
Rotary 3
Rotary 4
Rotary 5
ANALOG
DIGITAL
XGA
WXGA
SXGA
1080/50p
1080/60p
_ _
ON
OFF
PC1
ANALOG
A.SET
FORMAT
SXGA
ON
To select the DVI-I IN connector input
3ELECT;!.!,/'=OR;$)')4!,=USINGTHEROTARYCONTROL
To select the input signal format
3ET;&/2-!4=USINGTHEROTARYCONTROL
The source input from PC is displayed in the selected
SIGNALFORMAT(OWEVERITISRESIZEDACCORDINGTOTHE
settings of the video format (
PAGE
To execute auto setup of analog input
Select ON using the rotary 5 control, and press the
KEY
7HENTHEMESSAGE;/+=APPEARSPRESSTHE KEYAGAIN
To cancel the execution, press the
KEYWHILEHOLDING
DOWNTHE3()&4KEY
NOTE
When switching is being made between [ANALOG] and
s
[DIGITAL], the message “Please Wait…” appears, and
disappears upon completion of switching.
When auto setup is executed, the image must be shown in
s
the entire display area of the screen. When auto setup is
being executed, the message “Please Wait…” appears, and
disappears upon completion of auto setup.
If auto setup is not successful, * appears under [A.SET].
Auto setup may become unsuccessful due to insufficient
automatic screen adjustment depending on the input image.
In this case, use the rotary 1 control to select [PC2] and
adjust [H POSI], [V POSI], [PHASE], and [CLOCK].
If the system format is 1080/50p or 1080/60p when DIGITAL
s
or ANALOG is selected, auto setup is disabled. In this case,
“---” appears under [A.SET].
Summary of Contents for AG-HMX100P
Page 47: ...MEMO 47 ...
