34
Basic Oper
ation
NOTE
If the AUDIO FOLLOW VIDEO button has been pressed to turn
on to interlock the audio faders with the transition lever or the
audio level of input source 5 to 8 has been adjusted with the
SHIFT key pressed, the audio fader settings may not match the
actual audio level.
In such a case, the audio level is adjusted as follows according
to the operation of the audio faders:
When the audio fader is moved in the direction in which a
s
difference with the actual audio level decreases, the audio
level does not change until the fader position matches the
actual audio level.
When the audio fader is moved in the direction in which a
s
difference with the actual audio level increases, the audio
level changes according to the fader position.
The audio level adjusted by the MASTER fader changes
s
according to the fader position.
AB Transition
AB transition is an effect of switching from source video A
to source video B, and vice versa.
4HEREARETWOMETHODSOFVIDEOSWITCHINGhWIPEvAND
hMIXv
Transition wipe
s
3OURCEVIDEO"OR! APPEARSBYWIPINGOUTSOURCE
VIDEO!OR"
Transition mix
s
3OURCEVIDEO"OR! APPEARSBYOVERLAPPINGSOURCE
VIDEO!OR"
The following diagram shows an example of transition wipe.
Transition is executed with the transition lever or the AUTO
4!+%BUTTON
1
Set [TYPE] to [AB] in the [BUS] submenu of the
[SETUP] menu (
page 27).
2
Select source video A and source video B
(
page 33).
3
Slide the transition lever to the A side (or B
side).
4
Select the transition pattern to use (
“To select
a pattern” on page 35).
Patterns registered as direct patterns (
PAGE
can be used.
5
Process the selected pattern by applying
effects including border, shadow, and trail
(
page Vol.2-3).
6
Set the pattern position (transition start
position) using the joystick.
0RESSTHE#%.4%2BUTTONTOTURNONANDTHEPATTERN
position is set to the center.
0RESSTHE(/,$BUTTONTOTURNONANDTHEJOYSTICKIS
fixed to the current position.
NOTE
There are some patterns for which the position
s
cannot be adjusted with the joystick.
For more information, refer to “List of Transition
Patterns” at the back of Volume 2.
For the patterns registered as direct patterns, the
s
settings of the effects or position applied to each
pattern are saved in memory and applied when the
pattern is called next time (if [MODE] in the [SETUP]
menu is set to [PRESET]). Any settings made for the
patterns not registered as direct patterns are not
saved in memory.
7
Set the transition time (from switching start to
end) (
“To set the transition time” on page 35).
8
Slide the transition lever to the B side (or A
side) or press the AUTO TAKE button.
7HENTHE!54/4!+%BUTTONISPRESSEDITISLIGHTED
and the source video switching is automatically
EXECUTEDAUTOTRANSITION FROM!TO"OR"TO!
To temporarily stop auto transition
0RESSTHE!54/4!+%BUTTONAGAIN
4HISBUTTONmASHESANDTHEVIDEOSWITCHINGISPAUSED
When the button is pressed again, it is lighted and the
switching is resumed.
To limit the transition to one direction
7HENTHE/.%7!9BUTTONISPRESSEDTOTURNONINTHE
0!44%2.AREATHETRANSITIONGOESINTHESAMEDIRECTION
regardless of the direction in which the transition lever is
MOVED.OTRANSITIONISREVERSED
(OWEVERIFATRANSITIONPATTERNWHICHISNOTREVERSED
INTRINSICALLYISSELECTEDTHE/.%7!9BUTTONmASHESWHEN
it is pressed.
To synchronize the audio faders to the
transition lever
0RESSTHE!5$)/&/,,/76)$%/BUTTONTOTURNON
Summary of Contents for AG-HMX100P
Page 47: ...MEMO 47 ...
