– 144 –
Chapter 8 Using SmartUI — Menu list
Screen
Corresponding button
Setting details and setting value
SET02:MON/HDMI
FORMAT
Sets the formats of video output from the <MON OUT> and <HDMI> terminals.
<
%
/REW> button
[MON]
Sets the signal format type output from the <MON
OUT> terminal.
With this setting, the signal format to be out put
from the <HDMI> terminal is also switched.
[AUTO] (HDMI:[1080i/720P])
Displayed only in the HD mode.
The SDI signal is output according to the setting
of the [SYSTEM MODE] item on the setting menu
[SYSTEM SETUP] screen.
f
The 1080i or 720P signal is also output from the
<HDMI> terminal according to the [SYSTEM
MODE] item setting.
f
For [1080-23.98PsF], the signal pulled down to
1080/59.94i is output from both <MON OUT> and
<HDMI> terminals.
[480i] or [576i] (HDMI:[480P] or [576P])
Displayed only in the HD mode.
The SDI signal of 480i or 576i is output.
f
The 480P or 576P signal is output from the
<HDMI> terminal.
[SDI] (HDMI:[480P] or [576P])
Displayed only in the SD mode.
According to the setting of the [SYSTEM MODE]
item on the setting menu [SYSTEM SETUP] screen,
the SDI signal of 480i or 576i.
f
The 480P or 576P signal is output from the
<HDMI> terminal.
[VBS] (HDMI:[480P] or [576P])
A composite video signal is output.
f
The 480P or 576P signal is output from the
<HDMI> terminal.
<STOP> button
[D.CON]
Sets the aspect for the down-conversion output
signal in the HD mode. This item is not displayed in
the SD mode.
[CROP]
Side-crop mode (Crops the left and right edges.)
[L.BOX]
Letterbox mode (Adds black bands at the top and
bottom of the image.)
[SQU]
Squeeze mode (Squeezes images horizontally.)
SET03:MON/HDMI
SETUP
Sets the output setting of the <MON OUT> and <HDMI> terminal.
<
%
/REW> button
[OUT]
Enables or disables the output from the <MON
OUT> terminal.
[ON], [OFF]
<STOP> button
[CHR]
Specifies whether characters are superimposed
over the output from <MON OUT>, <HDMI>, and
<REMOTE> terminals.
[ON], [OFF]
This setting is disabled when a remote control unit (AG-EC4G) is connected, and the settings on the
remote control unit or extension control unit supersede.
<FF/
)
> button
[ZBR]
Specifies whether the zebra pattern is
superimposed over the output from <MON OUT>,
<HDMI>, and <REMOTE> terminals.
f
This setting is not available when the setting
menu on the viewfinder screen is open.
[ON], [OFF]
SET04:LCD
Performs the display settings of SmartUI.
<FF/
)
> button
[
−
]
Decreases the setting value of the selected item. Press and hold this button to continuously decrease the
setting value.
<PLAY/PAUSE> button
[
+
]
Increases the setting value of the selected item. Press and hold this button to continuously decrease the
setting value.
<RESET> button
[RST]
Resets the setting value of the selected item to its factory setting value.
<MONITOR SEL> button
[
→
]
Moves the item selection to the right. When the item selection moves to the right edge, it moves back to
the left edge.
[BACK LIGHT]
Sets the luminance of SmartUI.
[1] ... [3] ... [5]
[CONTRAST]
Sets the contrast of SmartUI.
f
The SmartUI screen may be hidden depending
on the setting value.
In such a case, press the <HOME> to return to
the [HOME] screen and hold down the <LIGHT>
and <RESET> buttons. The setting value of
[CONTRAST] is reset to the factory setting.
[0] ... [33] ... [63]
indicates factory setting values.
